兰化化肥厂灰水回收管线涡轮增压清管器清洗方案.doc

中国石油天然气股份有限公司兰州石化分公司 动力车间灰水回水管道 涡轮增压清洗清洗方案 编制： 校核：审核：赵丽萍 批准：刘志新 甘肃黑马石化工程有限公司 二〇年月日 目 录 1、编制依据·······································································································1 2、动力车间灰水回水管道涡轮增压清洗·······················································3、··················································································2 4、·······································································2 5、···········································································3 6、················································································4 7、·····································································································11 8、清洗·····························································································11 9、·············································································11 10、···························································································11 11、清洗工程安全措施及施工管理····································13···················································································15 13、···················································································17中油兰州石化分公司化肥厂动力车间 灰水回水管道涡轮增压清洗施工方案1、编制依据： 本方案是根据车间管道的工艺流程，过程中产生氧化铁垢等有关技术资料而编制的，同时还参考了如下技术资料： HG/T2387-2007《工业设备化学清洗质量标准》。2、车间管道清洗车间系统～这些污垢附着在，必须采用有效的清洗方法清除这些污垢。.2选择清洗的范围 本次清洗范围为车间清洗前的准备工作 .1发包方 4.1.1清洗现场应三通一平，即水、电应充足，电源要可靠，地面平整。 ～.2承包方 4.2.1准备好涡轮增压器等清洗设备。 4.2.2保证涡轮增压器跟踪定位仪能按要求投用。 4.2.3所有施工工具、机械、材料、在合同签订后，按照发包方要求提前进入施工现场。 5、施工组织机构及施工准备 5.1施工组织机构 项目部 项目经理：刘建锋 安全负责人：刘涛 技术负责人：郭琦 质检负责人：盖普泉 一班组：浩万宏 二班组：李节平 三班组：丁天相 5.2施工准备 首先项目部做好进场前的准备，并成立联合小组对现场清洗勘察了解。根据图纸设计，管道运行情况，以及管道输送障碍等。做到清洗前全面掌握并加以处理，直至符合清洗条件。在此之前要查清管道走向和弯头位置，沿线作好标记，以便清洗时进行全程电子定位跟踪。根据管道实际情况，制作发射装置、接收装置等。购置清洗所需的阀门、法兰、弯头等其它所需材料。准备工作要做到即严密又周到，为清洗工作打下坚实的基础。 5.3施工条件 5.3.1建立健全的现场组织机构和严密的管理制度。 5.3.2进厂前搞好质量、安全教育及培训，施工人员经过技术培训和技术交底，对所承担的项目质量、工艺、安全要求等能清楚明白。 5.3.3搞好安防学习教育，有具体安防措施及设施，确保安全教育到位、措