33-《机械设计基础》试题（33 - fundamentals of mechanical design）.docVIP

下载本文档

1
0
约9.46千字
约 10页
2017-07-21 发布于河南
举报
版权申诉

33-《机械设计基础》试题（33 - fundamentals of mechanical design）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

33-《机械设计基础》试题（33 - fundamentals of mechanical design）

33-《机械设计基础》试题（33 - fundamentals of mechanical design） Basic mechanical design test 1. Fill in the blanks (1 point per blank, 30 points) The design criterion with drive is guaranteed, and has certain. 2. The key to thread protection is prevention. 3. The lubrication of sliding bearing is reduced, and the oil groove of the bearing shaft should be opened. 4. The combination of rolling bearing inner ring and shaft neck is adopted. The coordination of outer ring and seat hole should be adopted. 5. The diameter of the radial sliding bearing is doubled, the diameter ratio is constant, the load is constant, and the bearing pressure is the original In The Times. 6. When designing a pair of gear with decelerating soft tooth, the hardness of large and small gears should be higher when the hardness of large and small gears is required. In the hinged four-bar mechanism, the shortest rod of the two-crank mechanism is the sum of the remaining two lengths of the length of the longest rod. 8. When working on a flat key, rely on transmission torque. 9. In chain transmission, the number of links is often taken, and the number of chain teeth is often used. 10. Under the same conditions, the frictional force generated by v-belt transmission is much larger than that of the flat belt, because the force on the contact surface is greater than that of the belt. When two axes, the worm drive can be used. From reduced stress concentration, it is good to make the flat key slot on the shaft to be processed by milling cutter. 13. According to the bearing form of the axial class, it can be divided into the axis of transmission and transmission The transmission shaft, as well as the spindle that is not passed. 14. The speed of the sprocket, the pitch, the number of teeth, the greater the dynamic load of the chain drive. In cylindrical gear transmission, the diameter of the gear decreases, and the bending strength of the tooth is made The stability of contact strength and transmission. 16. The coupl