控制卡常见问题与解答（Common problems and solutions of control card）.docVIP

下载本文档

3
0
约8.03千字
约 8页
2017-07-22 发布于河南
举报
版权申诉

控制卡常见问题与解答（Common problems and solutions of control card）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

控制卡常见问题与解答（Common problems and solutions of control card）

控制卡常见问题与解答（Common problems and solutions of control card） Common problem First, the computer and control card communication is not up A, please check whether your computer and control card communication line (or cable, or GPRS connection) is connected properly; B, please check the control card dial number and bit rate screen dial switch is with you in the software settings screen parameters corresponding to (try to switch the call in the past, then re dial back, near here, including numerical) set aside special rate and screen number; C, check whether the control card you are using corresponds to the control components you choose on your software; D, please check the serial port of your computer and the serial port settings on your software; E, please check whether the jumper cap on the control card is the jumper cap of the 232/485 in your chosen communication mode; F, please check whether your chosen communication method is consistent with the software settings: for example, 232/485 communication mode, network communication mode, or GPRS communication mode; G, please get the controller closer to the computer for testing, or for a lower dial rate test; Remarks： Definition of A, 8 bit toggle switch P0~P7 is the dial screen number. When P0~P7 is in the OFF state (near the numerical side), it is the number 1 screen. When P0 is ON and P1~P7 is the OFF state, it is screen No. 2... Uh, set to the specific P0~P7 OFF state of 0 times the equivalent of a superscript, when the P0~P7 is in OFF state, is a screen, when the P0 dial to ON state, the other is OFF, 20+1=2 is 2 screen, and so on......... . The screen number of all screens is 2, how many times plus 1?. B and B0~B1 are dial rates, and they have two states: ON and OFF. (1) when the B0 and B1 are OFF States, the dial rate is 9600, near the value side; (2) when B0 is the ON state, when the B1 is OFF, the dialing rate is 28800, that is, 1 is near the value, and 2 is near the left; (3) when B0 is the OFF state, when the B1