3-gridpro教程三——相交表面的网格创建（3-gridpro tutorial three - mesh creation of intersecting surfaces）.docVIP

下载本文档

224
0
约1.47万字
约 10页
2017-07-23 发布于河南
举报
版权申诉

3-gridpro教程三——相交表面的网格创建（3-gridpro tutorial three - mesh creation of intersecting surfaces）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

3-gridpro教程三——相交表面的网格创建（3-gridpro tutorial three - mesh creation of intersecting surfaces）

3-gridpro教程三——相交表面的网格创建（3-gridpro tutorial three - mesh creation of intersecting surfaces） GridProGridProGridProGridPro is very important for grid design at both sides of the grid when doing a lot of design analysis. Sometimes, we only need to analyze some of the structures, and the rest of the structure does not need to create meshes. In the first chapter of this tutorial, well explore how to create an inner mesh on a 2 dimensional surface and set a curved intersection surface to mesh boundaries. In the second chapter, we will create a mesh for a similar 3 dimensional geometry, and introduce the functions of tangent planes in complex topology design. Learning Guide: how to create 1. intersecting planes to adjust the grid density of 3. wrap2. interactive real-time automatic read grid file operating at 4. grid view surface operation mode is displayed in the operation of wrapwrapwrapwrap in tutorial two we learn the double surface topology association plays an important role in the cross on the surface of the mesh quality. The same concept will be applied in tutorial three. First, click and load the TIL file Tutorial_3_part1.fra to azmanager. The geometry of the document will appear as shown in the following figure. Close the cutting plane to the global coordinate system to reduce the clutter in the drawing area. The goal of this topology design is to create grids for the stems under the mushroom structure. The curved surface of the mushroom cover that crosses the stem will be set as a boundary of the mesh. First, create a rectangular topology around the stem. Look at the picture below. Add the topology above to the topology group 1, and then create a wrap that shrinks by 25%. Look at the picture below. Since we only need to create a mesh at the stem of the structure, we delete the top topological lines. When creating an inner mesh, the topology and surface assignments are different from those created outside the grid. We will assign the topology outer layer to the su