浅谈彩电高压帽打火的原因（Discussion on the causes of high voltage cap sparking）.docVIP

下载本文档

5
0
约 4页
2017-07-24 发布于河南
举报
版权申诉

浅谈彩电高压帽打火的原因（Discussion on the causes of high voltage cap sparking）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

浅谈彩电高压帽打火的原因（Discussion on the causes of high voltage cap sparking）

浅谈彩电高压帽打火的原因（Discussion on the causes of high voltage cap sparking） Discussion on the causes of high pressure cap ignition of color TV, elimination methods and more 2011-08-31 22:30 Color TV kinescope high-pressure nozzle and is connected between the graphite layer distance of more than 20000 volts. After the use of color TV for a period of time, the high pressure mouth produces a phenomenon of fire, nothing more than the following three reasons: (1) dust in the air more. The TV work process, due to the high voltage electrostatic induction and absorb dust around the high-pressure cap, the insulation performance; (2) air humidity, pressure cap sealing, the high-pressure cap TV repair into the humid air; (3) high voltage and high voltage wire connected with the circlip solder burr, burr will produce the phenomenon of point discharge, high pressure rubber cap burning aging. The high voltage nozzle of the colour TV set can be eliminated by using the following methods: (1) discharge the high pressure nozzle first. Remove and burn high pressure cap and circlip. If there is little dirt on the high pressure nozzle and the surrounding graphite layer, it can be washed with alcohol and cotton. If the dirt is thicker, it can be scraped with a sharp blade. Such as high pressure nozzle rust, sandpaper and other polished, the high pressure nozzle inside the residue completely clean. After cleaning, use the electric hair dryer to heat the water near the high pressure nozzle and nearby. (2) press the high tension line into the new high pressure cap welding spring. Clamp spring and high voltage line must be smooth, must not have burr, otherwise, heavy, then a power on the ignition, light use, will soon high-pressure cap aging, affecting service life. (3) do the sealing work of high pressure cap. This step is critical. There are two ways to enter the humid air in the high-pressure cap: one is the edge of the high pressure cap; the other is the hole that the high voltage line penetrate