约克压缩机传感器校验程序（York compressor sensor calibration program）.docVIP

下载本文档

7
0
约5.22千字
约 6页
2017-07-24 发布于河南
举报
版权申诉

约克压缩机传感器校验程序（York compressor sensor calibration program）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

约克压缩机传感器校验程序（York compressor sensor calibration program）

约克压缩机传感器校验程序（York compressor sensor calibration program） After the compressor is finished, the proximity sensor and potentiometer are installed in the York factory, or installed on-site, or the compressor is reloaded at the site to a predetermined location. This value should be referred to as a reference position, followed by steps. This value is not changed until the compressor is reloaded or the proximity sensor and potentiometer have been replaced. Note: the reference position value must be operated in the microcomputer control center, such as microcircuit board or RTC (U16), which is replaced by the following program: 1) switch the compressor switch to stop / reset position 2) press the access code to display the input access code 3) 1380 carriage return 4) enter authorized programming mode 5) press programming to display programming mode and select set values 6) press the mode button to show the current mode of operation 7) press the date push / scroll screen key until the select repair operation mode appears. Each time the key is pressed, different patterns appear 8) carriage return, appear programming mode, select the set value 9) press access code to show invalid access to programming 10) press the model key to appear maintenance mode; if not appear, start again from the first step. 11) according to the access code key, the input access code appears 12) 1397 carriage return 13) shows access authorization programming 14) press programming to display the programming mode and select the setting value 15) press the display data key The proximity sensor is programmed for 2 seconds Start the oil pump for 2 seconds, and the oil pump opens automatically Show oil pressure XXX, PSIG25, minimum program until the oil pressure exceeds 25.0PSIG (press the oil tank key, if necessary, turn off the oil pump and switch to programmed mode / transient information) Show press enter to check proximity sensor 16) press carriage return to show actual position = XX MILS; reference