回弹仪常见问题及维修（Common problems and maintenance of rebound instrument）.docVIP

下载本文档

37
0
约6.32千字
约 5页
2017-07-25 发布于河南
举报
版权申诉

回弹仪常见问题及维修（Common problems and maintenance of rebound instrument）.doc

1、本文档共5页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

回弹仪常见问题及维修（Common problems and maintenance of rebound instrument）

回弹仪常见问题及维修（Common problems and maintenance of rebound instrument） A bomb attack in the test, the pointer stopped at the starting position without moving the slider: 1. pointer spring break, the spring in the elastic hammer struck the hanging elastic hammer, the pointer stopped at the starting position without moving the slider. Maintenance method: replace the spring piece. 2., the take-off position of the hammer is not qualified, causing the pointer block to stop at the starting position. Maintenance method: adjust the position of the nut of the back cover and make the position of the hammer reach 100 lines. 3. pointer pointer slider relative to the pointer shaft angle is too small, then the pointer in the process of elastic hammer impact friction force is too small, so that the pointer does not slide. Maintenance method: remove the pointer part, pull the appropriate large angle, within the prescribed scope. Rising position, not moving 1. pointer pointer slider relative to the pointer shaft angle smaller than the pointer in the process of elastic hammer impact friction force is relatively small, so that the pointer does not slide. Maintenance method: remove the pointer part, pull the appropriate large angle, within the prescribed scope. With the loose 2. pointer slider and the pointer shaft, then the friction force between the pointer and the pointer shaft is too small, can not make the spring normally on elastic hammer, it will shake to a fixed location. Maintenance method: remove the pointer, appropriate that the small reed angle in the specified range. The 3. indicator slider is rubbed against the shell or scale to increase the friction force during the sliding of the index and to wobble to a certain position. Maintenance method: use small file, appropriate file, pointer, slider, flat or two shoulder, until friction elimination. Button not available 1. the buffer spring is jammed by the button and can not move. Maintenance method: open the back cover, remove the