检查和处理电动机故障的方法（Method for checking and handling Motor Faults）.docVIP

下载本文档

6
0
约1.04万字
约 7页
2017-07-27 发布于河南
举报
版权申诉

检查和处理电动机故障的方法（Method for checking and handling Motor Faults）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

检查和处理电动机故障的方法（Method for checking and handling Motor Faults）

检查和处理电动机故障的方法（Method for checking and handling Motor Faults） Method for checking and handling motor faults.Txt Method for checking and handling Motor Faults There are many kinds of methods for dealing with the faults of motors. Some are from principle analysis, others are experience. Through decades of work experience, the author makes a detailed analysis of the combination of theory and practice. The motor can not start 1. the motor does not rotate and there is no sound. The reason is that the motor power supply or winding has two phase or three phase open circuit. First, check if there is a power supply voltage. If there is no voltage in three-phase, it shows that the fault is in the circuit; if the three-phase voltage is balanced, the fault is in the motor itself. At this time, the resistance of the motors three-phase winding can be measured to find out the winding of the broken phase. 2., the motor does not turn, but there is a buzz sound. Measuring the terminal of a motor, such as the balance of the three-phase voltage, is rated as a serious overload. The inspection procedure is to remove the load first, and if the speed and sound of the motor are normal, the overload or load mechanical part can be judged to be faulty. If you still dont turn, turn the motor shaft by hand, if it is tight or not to move, is measured as the three-phase current, three-phase current balance, but lower than the rated value is likely to be the motor mechanical part is stuck, motor oil, rust, or serious damage to the bearing cover or cover with oil so, the rotor and the inner oblique collision (also called sweeping). If the hand rotating motor shaft to a certain angle are more difficult to hear or periodic Tsatsa sound, can be judged as sweeping. The reasons are as follows: (1) the gap between the inner and outer rings of the bearing is too large, and the bearings need to be replaced; (2) the bearing chamber (Zhou Chengkong) is too large and wears out for a long time, resulting in too