硒鼓加粉技巧（Toner cartridge powder adding technique）.docVIP

下载本文档

79
0
约1.31万字
约 11页
2017-07-27 发布于河南
举报
版权申诉

硒鼓加粉技巧（Toner cartridge powder adding technique）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

硒鼓加粉技巧（Toner cartridge powder adding technique）

硒鼓加粉技巧（Toner cartridge powder adding technique） Toner cartridge powder adding technique HP C3900A cartridge (HP 4V/4MV/4VC) Canon EP-B cartridge (CANON LBP-BX) A separate cartridge. Open the machine to remove the toner cartridge on the table, first pick a spring on the drum, with oblique mouth clamp to one side of the metal pin pulled out outwards, on both sides of the silver metal pin can be pulled out after the toner cartridge is divided into two parts, with drum core is a waste powder collection. With a magnetic roller for powder silo. The White plastic clip two. Replace the drum core and the scraper, clean up waste powder waste collection of grey powder in the photosensitive drum on both sides of the screws on the screw off, pull out the white plastic clips, drum core can be taken out. Then the discharge roll out, twist off out of the two screws on the scraper scraper, the waste powder completely clean, then the scraper, discharge roller, drum by the demolition of the state before the recovery (note that the drum core and two white plastic clips and the discharge roller direction cannot reverse). Gently turn the drum core ring, drum surface should be clean. If there is residual powder on the drum surface, the scraper shall be replaced in time. The Three. If you are filling toner cartridges filled with the original cartridge toner without first filling, the filling will not need to clean up the powder bin and a magnetic roller, otherwise must put the powder bin and a magnetic roller on the toner clean. Take out the plastic cover on the powder bin, shake the ground 4V/4VC toner, and then slowly pour into the powder bin, cover the plastic lid, and gently rotate the magnetic roller several times. The magnetic roller should be able to adsorb the toner evenly. The Four. The assembly cartridge will be available for powder storehouse and waste powder collecting parts according to the open position installation restoration, inserted on both sides of the metal pin on the