- 1、本文档共16页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
优质模具制作齐步(High quality in mould making)
优质模具制作齐步(High quality in mould making)
High quality mold mold making in 2009-12-12 20:36 production of top quality, from the factory hardware, management level, personnel training three aspects and reach the standard of excellence. Solid and effective work must be done in the selection of mould materials, the reasonable arrangement of technological procedures, and the quality control.
I. conditions for manufacturing moulds:
1. Environmental conditions
Temperature: the ideal range of temperature is 21-28 degrees C. The environment temperature shall always be maintained during the manufacture of the mold and die. The matrix material used in die manufacturing should have the best chemical reaction process, and the environmental factors are not suitable, which will prolong or accelerate the process, and have a negative impact on the performance of the mold.
Humidity: relative humidity has important effect on the gel coat resin curing and, if in the manufacture of molds the relative humidity is greater than or equal to 70, adversely affect the curing of the substrate material should be careful and should wait until the appropriate conditions of production or take dehumidification measures.
2 、 perfect workshop management
The workshop for mold manufacturing shall have the storage conditions of chemical products, the equipment for controlling temperature and humidity and the clean work site. Management needs to have classified the process set area, process card, work instructions, quality tracking card and the control file is complete, detailed record.
3 compressed air
Pure, dry gas supply is another element in the manufacture of high-quality molds. In the trachea of a small amount of water or oil will bring important influence to the gel mold. An air compressor in a good environment shall be matched and equipped with an effective air dryer and an oil-water separator, as well as a voltage stabilizing and regulating system.
4, raw materials
Selecting the best quality raw ma
您可能关注的文档
- 伴你成长(Grow up with you).doc
- 保健品会销形式的晋级与改革战略(Promotion and reform strategy of health products in the form of marketing).doc
- 保健品分类().doc
- 保安服务手册(Security Service Manual).doc
- 保守国家秘密知识竞赛(Keep secret knowledge contests).doc
- 保护接(Protective connection).doc
- 保定周边旅游景点介绍及路线指南(Introduction to tourist attractions and route guides around Baoding).doc
- 保密题库【公务员】(Secret questions library [civil servants]).doc
- 保持精力充沛(Stay energetic).doc
- 保持人材优先的开展计谋!(Talent development strategy!).doc
文档评论(0)