座便器安装规范及注意事项（Toilet installation specifications and matters needing attention）.docVIP

下载本文档

10
0
约6.88千字
约 6页
2017-08-02 发布于河南
举报
版权申诉

座便器安装规范及注意事项（Toilet installation specifications and matters needing attention）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

座便器安装规范及注意事项（Toilet installation specifications and matters needing attention） Decoration, toilet installation is critical, acceptance is also very exquisite, not only to see the final result, let the construction workers according to the specifications in the installation process, avoid the hidden danger to the future life. So what are the installation specifications? Installation steps of toilet: (1) take out the pipe plug at the ground inlet, and clean the pipe around the pipe after checking that there is no debris. (2) the water outlet pipe of the toilet is aligned with the water inlet pipe and is leveled to look for the right place. The marking is made at the bolt hole of the toilet and the toilet is removed. (3) in a mark hole diameter of 20 mm, 60 mm deep, the diameter of 10 mm was inserted into the bolt hole, with cement twist firmly, the toilet seat eye alignment bolt placed, and make the mark consistent test after the toilet away. The toilet water outlet and water pipe around with putty, then four bolt holes Zuopianqi alignment bolt, flat is a bolt, a rubber pad, screw nut, screw to moderate. (4) at the toilet after the end of the center, draw a vertical line from the ground, at a height of 800 mm horizontal painting, according to the two side hole of the water tank in the back position, horizontal line drawing mark, holes in the hole to seal the diameter of 30 mm, 70 mm deep. Insert a bolt with a diameter of 10 millimeters and a length of 100 millimeters into the hole and twist it with cement. The back water tank is hung on the bolt, flat to find the right, especially with the toilet center alignment, bolt on good rubber pad, screw nut, twist to the tightness. (5) when installing the back elbow of the back water tank, the nut of the water inlet of the back water tank and the water inlet of the toilet bowl is dismounted first, and the back cover is sheathed on the sewer elbow, and the rubber pad is respectively sheathed on the sewer pipe. The upper end of