各种加工方法能达到的表面粗糙度（Surface roughness achieved by various processing methods）.doc

下载文档 降价啦

13
0
约6.38千字
约 20页
2017-08-04 发布于河南
举报
版权申诉
保障服务

各种加工方法能达到的表面粗糙度（Surface roughness achieved by various processing methods）.doc

1、本文档共20页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

各种加工方法能达到的表面粗糙度（Surface roughness achieved by various processing methods） The surface processing method can achieve the roughness of the.Txt character itself is not good or bad, optimistic and pessimistic both contribute to the world, the former invented the airplane, who invented the parachute. The surface roughness of machining method can achieve ID processing method of surface roughness of Ra (m) One Automatic cutting, sawing or cutting circular saw From 50 to 12.5 Two Cut off (car) From 50 to 12.5 Three Cut off (milling) From 25 to 12.5 Four Cut off (wheel) From 3.2 to 1.6 Five Turning round (rough) From 12.5 to 3.2 Six Turning round (semi finishing metal) From 6.3 to 3.2 Seven Turning round (semi finishing metal) From 3.2 to 1.6 Eight Turning round (metal finishing) From 3.2 to 0.8 Nine Turning round (non metal finishing) From 1.6 to 0.4 Ten Turning round (precision car or car diamond metal) From 0.8 to 0.2 Eleven Turning round (car or car non diamond precision metal) From 0.4 to 0.1 Twelve Turning end (rough) From 12.5 to 6.3 Thirteen Turning end (half pure metal) From 6.3 to 3.2 Fourteen Turning end (semi refined car non metal) From 6.3 to 1.6 Fifteen Turning end (metal finishing) From 6.3 to 1.6 Sixteen (non metal turning end surface finishing From 6.3 to 1.6 Seventeen Turning end (precision metal car) From 0.8 to 0.4 Eighteen Turning end (precision metal car) From 0.8 to 0.2 Nineteen Slot (trip) Twelve point five Twenty Slot (two trips) From 6.3 to 3.2 Twenty-one High speed turning From 0.8 to 0.2 Twenty-two Drill (less than 15mm) From 6.3 to 3.2 Twenty-three Drill ( 15mm) From 25 to 6.3 Twenty-four Reaming, coarse (with skin) From 12.5 to 6.3 Twenty-five Reaming, fine From 6.3 to 1.6 Twenty-six Countersinking chamfering (hole) From 3.2 to 1.6 Twenty-seven Countersink flat with guide From 6.3 to 3.2 Twenty-eight Boring (boring) From 12.5 to 6.3 Twenty-nine Boring (semi boring metal) From 6.3 to 3.2 Thirty Boring (semi fine boring non metal) From 6.3 to 1.6