普通车床细长轴零件夹具设计方法（Ordinary lathe slender shaft fixture design method）.docVIP

下载本文档

4
0
约1.63万字
约 12页
2017-08-18 发布于河南
举报
版权申诉

普通车床细长轴零件夹具设计方法（Ordinary lathe slender shaft fixture design method）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

普通车床细长轴零件夹具设计方法（Ordinary lathe slender shaft fixture design method）

普通车床细长轴零件夹具设计方法（Ordinary lathe slender shaft fixture design method） Method of fine long axis of car (Part 2) Release: 2011-8-23 | - Author: | source: mahuaxiao | view: 647 | user attention: 1. under what conditions do you use the center frame and the heel rest? Answer: the turning axis, the workpiece fixture if it is stretched out over a length of 15 times the diameter of the smooth shaft (such as lathe bar), with chuck support tip, with knife clamping, or before and after the tip, with knife clamping support. Bench shafts (such as lathes, spindles, etc.) shall be fitted with chucks and central shelves. Some particularly long workpieces can also be fitted with chucks, support points, center racks, and tool holders. With this kind of additional clamping tool, the clamping rigidity of the workpiece can be increased, the processing quality can be guaranteed, the vibration can be reduced, the workpiece can be prevented from producing or bulging, and the geometric accuracy and the surface roughness of the workpiece can be improved 1. under what conditions do you use the center frame and the heel rest? Answer: the turning axis, the workpiece fixture if it is stretched out over a length of 15 times the diameter of the smooth shaft (such as lathe bar), with chuck support tip, with knife clamping, or before and after the tip, with knife clamping support. Bench shafts (such as lathes, spindles, etc.) shall be fitted with chucks and central shelves. Some particularly long workpieces can also be fitted with chucks, support points, center racks, and tool holders. The use of this kind of additional clamping tool, can increase the rigidity of the workpiece clamping, guaranteed the processing quality, reduce vibration, avoid the workpiece or bulging, improve the geometric accuracy and surface roughness, and can be used for processing large amount of cutting, and improve labor productivity. 2. how to load and correct the workpiece with the center frame? Answer: when the workpiece is