机械设计禁忌500例（500 cases of mechanical design taboo）.docVIP

下载本文档

4
0
约3.34千字
约 2页
2017-08-18 发布于河南
举报
版权申诉

机械设计禁忌500例（500 cases of mechanical design taboo）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

机械设计禁忌500例（500 cases of mechanical design taboo）

机械设计禁忌500例（500 cases of mechanical design taboo） The first chapter taboo 500 cases of mechanical design improve the strength and stiffness of the structure design of 1.1 point support points and avoid too far away to avoid or reduce the 1.2 cantilever structure cantilever length 1.3 do not ignore the work load can produce the beneficial effects of 1.4 vibration load components to avoid friction force transmission mechanism in 1.5 to avoid the unbalanced force to avoid 1.6 only consider the single force transmission route 1.7 should not be ignored in the work for the stress distribution of the deformation effect of cast iron by 1.8 to avoid large tensile stress 1.9 avoid rod bending stress under impact load of 1.10 parts to avoid the stiffness of 1.11 stress components to avoid excessive surface roughness and scratches by 1.12 allergic parts should avoid surface residual tensile stress of 1.13 variable load parts should avoid or reduce the stress concentration of 1.14 to avoid the effect of local strength The structure is too close to 1.15 pre deformation direction and avoid the work load of the same 1.16 wire rope pulley and drum diameter is too small to avoid the 1.17 wire rope bending times too much, pay special attention to avoid repeated bending 1.18 lifting wire rope and reel connected to left margin The middle parts of 1.19 can not force the force should be avoided as far as possible to avoid additional stress generated 1.20 axis misalignment when installing 1.21 to minimize the effect on the foundation of the second chapter to improve the wear resistance of the structure design to avoid the same material with 2.1 sliding friction pairs 2.2 to avoid white alloy wear resistant layer thickness is too large to avoid 2.3 to improve the surface wear resistance and improve the whole parts of the 2.4 parts to avoid local wear caused by the scrap parts 2.5 white alloy bearing lining, bearing should pay attention to the material selection and structure design of 2.6 be