supex1(siei)-随机文件复印使用（Supex1 (siei) - random file copy use）.docVIP

下载本文档

1
0
约6.01千字
约 10页
2017-08-20 发布于河南
举报
版权申诉

supex1(siei)-随机文件复印使用（Supex1 (siei) - random file copy use）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

supex1(siei)-随机文件复印使用（Supex1 (siei) - random file copy use）

supex1(siei)-随机文件复印使用（Supex1 (siei) - random file copy use） Explanation: This debugging instruction only applies to the electric control system of LCB-IITOMCB SIEI converter. Please read the book before you debug, I believe that your debugging work will have no small help! This book describes the process of learning from the motor tuning to the completion of the well. I. inspection prior to power on The electrical control principle diagram check circuit, safety circuit, the brake circuit wiring. Two 、 motor self regulation (please note)!!! The following self tuning method is carried out under the no-load condition of the main engine! The motor is three-phase, please be strict with the inside of the control cabinet, please believe that this can save you a lot of time You little help: the parameter tree SIEI converter After confirming that the power supply can be safely switched on, the motor can be adjusted automatically (the power supply can only be supplied to the frequency converter and the main board can not be powered on). First, please reset the parameters of the frequency converter. The menu method is as follows: STARTUP STARTUP CONFIG = LOAD DEFULT, press the panel ENTER key, and then reset the parameter. Remember: after the parameter reset, you must save it again. The menu method is as follows: STARTUP = SAVE CONFIG Then the motor can be adjusted automatically: 1. parameter input: (1) Startup, Startup, Config, Enter, setup, mode,, Drive, Data Phi Mains voltage=400V Phi Ambient temp=40 Phi Switching freq=8kHZ Phi Spd ref/fbk res=0.03125rpm Motor, Data Phi Rated Voltage=380V Phi Rated Current=** A (motor rated current) Phi Rated, Speed=**, RPM (motor rated speed) Phi Pole Pairs=** (Note: this value is extremely logarithmic) Phi Torque Constant=** (rated torque divided by the rated current can be obtained this value) Phi Rated Power=** (motor rated power) Phi EMF Constant=0 (back EMF, set to 0, by self-tuning) Phi Stator resist=0 (stator resistance is set to 0