- 1、本文档共57页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
收集的人结构素材图片,很有用处
收集人体结构素材图片人体的肌按结构和功能的不同可分为平滑肌、心肌和骨骼肌三种,按形态又可分为长肌、短肌、阔肌和轮匝肌。平滑肌主要构成内脏和血管,具有收缩缓慢、持久、不易疲劳等特点;心肌构成心壁;两者都不随人的意志收缩,故称不随意肌。骨骼肌分布于头、颈、躯干和四肢,通常附着于骨,骨骼肌收缩迅速、有力、容易疲劳,可随人的意志舒缩,故称随意肌。骨骼肌在显微镜下观察呈横纹状,故又称横纹肌。?? ???骨骼肌是运动系统的动力部分,在神经系统的支配下,骨骼肌收缩中,牵引骨产生运动。人体骨骼肌共有600多块,分布广,约占体重的40%。每块骨骼肌不论大小如何,都具有一定的形态、结构、位置和辅助装置,并有丰富的血管和淋巴管分布,受一定的神经支配。因此,每块骨骼肌都可以看作是一个器官。?? ? ? 头肌可分为面肌(表情肌)和咀嚼肌两部分。躯干肌可分为背肌、胸肌、腹肌和膈肌。下肢肌按所在部位分为髋肌、大腿肌、小腿肌和足肌,均比上肢肌粗壮,这与支持体重、维持直立及行走有关。
the same direction of rotation 90 ° or 180 ° for; after each disc rotor when measuring position alignment of the two half coupling constant, should also be in terms of accuracy and consistency. Surface deviation measurement, must in every 180 degrees corresponding to the two radii are equal to each other in order to eliminate errors caused by movement of the rotor. Only a support bearing of the rotor, WA couplings, such as the use of temporary leave the Center, should pay attention to keep the rotor in the measuring process in the center of the bearing oil retaining the nest does not change. Steam oil block, there should be sufficient clearance between the rotor and, in rotors make sure rotor is not on the block or seal oil. At the time of measurement, connections are not allowed between two rotors, each in a free State. Not allowed in case of assembled sleeve, Center work on the toothed coupling. Coupling tool should have adequate stiffness, installation must be secure and reliable. Coupling Center using a dial indicator, the table should be put in prison and avoid touching, to ensure correct measurement. Coupling disc after a week to return to the original position, circumference of dial gauge reading should be able to go back to the original value. When measuring the clearance of end, into the feeler of the gap should not exceed four at a time, when the gap is too large, you can use the gasket with the feeler gauge me
文档评论(0)