TMS320C2812电子磁罗盘补偿技术研究.docVIP

TMS320C2812电子磁罗盘补偿技术研究 摘要电子磁罗盘是一种利用地球磁场测量方向的重要导航工具，高精度的电子磁罗盘对提高导航定位技术，促进航空、航海以及国防事业发展具有重要的现实意义。已有电子磁罗盘面临的体积、重量、功耗大，误差补偿困难等问题亟待解决。 本论文介绍了电子磁罗盘的特性，详细研究了各类误差补偿算法的优缺点，采用基于BP神经网络的补偿算法，并且设计了由磁阻传感器HMC1021/1022、DSP微处理器TMS320C2812、微加速度计ADXL335组成的电子磁罗盘。根据传感器的输出特点，利用DSP芯片编写系统程序代码;分析磁阻传感器的各类误差来源，并通过误差补偿算法来提高系统的精度。 实验测试表明，研制的电子磁罗盘体积小、重量轻、功耗低小、成本低，在0-360度范围内航向角的测量精度从补偿前的19.2度减小到8度范围内，验证了基于BP神经网络的补偿算法的有效性，并且实现了实时补偿，满足了导航系统的要求。5453 关键词电子磁罗盘磁阻传感器误差分析补偿算法 设计说明书（论文）外文摘要 TitleStudy on error compensation methods of Electronic Magnetic Compass(EMC) Abstract EMC is an important device for navigation. High precise EMC plays a realistic role in improving navigation positioning technology and in the development of navigation , navigation and national defense. The present EMChas some problems need to be handled such as big volume, weight, power consume, hard to compensate error. This paper introduces the characters of EMC and detailedstudys the relative merits of all kinds of compensation algorithm. Using the compensation algorithm which is based on the BP neural network and designing an EMC consisted of magnetic sensor HMC1021/1022，acceleration sensor ADXL335 and DSP microprocessor TMS320C2812.According to the characteristic of magnetic sensor, using the disposing signal of DSP to write the procedure of the system. On a variety of possible errors of the magnetic sensor in analysis, a corresponding compensation is proposed to approach to improve the system accuracy. Experimental tests show that the developed EMC is small volume, low weight, power consume and cost. The heading angle of measurement accuracy is decreased tofrombetween, and realize real-time compensation, in order to meet the requirement of the navigation system. 3.2.1磁阻传感器HMC1021/102217 3.2.2 DSP芯片TMS320F281219 3.3硬件电路设计与分析20 3.3.1电源电路设计20 3.3.2信号调理电路21 3.3.3磁传感器置位/复位电路22 3.3.4磁传感器测量单元24 3.3.5ICETEK-F2812-A评估板介绍25 3.4小结26 4电子磁罗盘软件设计与实现27 4.1CCS软件开发平台27 4.2电子磁罗盘的软件模块及流程图28 4.2.1主程序流程图28 4.2.2系统初始化程序设计28 4.2.3数据采集子程序29 4