加工中心使用g54对刀（The machining center uses g54 to adjust the tool）.docVIP

下载本文档

2
0
约5.18千字
约 5页
2017-09-01 发布于河南
举报
版权申诉

加工中心使用g54对刀（The machining center uses g54 to adjust the tool）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

加工中心使用g54对刀（The machining center uses g54 to adjust the tool）

加工中心使用g54对刀（The machining center uses g54 to adjust the tool） G43 is the tool length compensation, G44 negative compensation, the machine executes the G43 direction of the tool movement and compensation value symbol, namely plus tool away from the workpiece, the tool workpiece near the minus sign. G44 and G43 instead of compensation. G43 is more intuitive, more application. In this example, the +40.0mm input 02 bias bias set cutter compensation at no., When executing the program section of No. 2 knife: C90G54GOX0Y0;: G43H2Z100.0; No. 2 point position and the reference implementation of G90G54GOXOYOZ100.0 knife position is consistent, the distance of the surface of workpiece is 100.0mm. So, No. 2 knife set through the tool length compensation, the origin and the origin of the coincidence of programming. 2. The method of machining center work multi cutter coordinates and cutter compensation length setting 1. Operation steps: (1) the workpiece clamping, with edge finder is to find and set the Y coordinate system, such as offset setting G54, Z zero. (2) will be required for machining tool number: T. T2, T; and installed on the handle?. (3) T1 installed on the spindle, spindle and workpiece moving above, with a height of 100.0mm gauge measuring and recording machine coordinate Z. (Z, will. 100) fill in the Settings in length bias. (4) above, the tool in the spindle with gauge measurement in turn and read, will (Z 100) in length bias settings in Hi, until all the tool setting is finished. Analysis: the tool will work axis X, Y direction set in the workpiece center, Z to the machine origin; each knife with each knife knife as a reference point. When the machine executable program G90G54G0x0Y0Z0; the knife and the knife spindle datum position. Obviously, this time, work coordinate origin and the origin of each knife Z programming direction does not coincide. Our analysis of the 1 knife, if the No. 1 can tip down H., and coordinate the work unchanged, and the origin is