co2气体保护焊焊接补充方案（Supplementary scheme for CO2 gas shielded arc welding）.docVIP

下载本文档

1
0
约6.27千字
约 7页
2017-09-03 发布于河南
举报
版权申诉

co2气体保护焊焊接补充方案（Supplementary scheme for CO2 gas shielded arc welding）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

co2气体保护焊焊接补充方案（Supplementary scheme for CO2 gas shielded arc welding）

co2气体保护焊焊接补充方案（Supplementary scheme for CO2 gas shielded arc welding） 1, overview In order to further improve the welding quality and welding speed of 2000m3C5 spherical tank in storage and transportation plant, CO2 gas protection shall be adopted to participate in the welding of C5 spherical tank. 2. Main features of CO2 gas shielded arc welding 2.1. The welding seam is beautiful, and the welding seam needs no polishing after welding, so the welding seam has uniform geometric dimension. 2.2, welding spatter, flux cored wire with arc stabilizer in its core, stable arc combustion, droplet in uniform droplet over, when welding spatter few splash and fine particles, cooling speed, generally in the shell plate is difficult to remove easily. 2.3, the shrinkage deformation of welding seam is small, because the welding heat input is concentrated, the heat affected zone is small, so the welding shrinkage deformation is small and the welding residual stress is small. 2.4, high welding efficiency, high current density filaments automatic welding, determines its higher melting fill speed, resulting in higher welding speed, and the automatic welding process and eliminates the need for frequent replacement of themanual welding electrode time. 3. Preparation before welding 3.1 welding groove: 3.1.1, weld groove is X groove. 3.1.2, welding groove should be smooth, no cracks, delamination, slag and other defects, size consistent with the provisions of the drawings. 3.1.3, groove surface and both sides of the 50mm welding, water, rust, oil, slag and other harmful impurities should be removed. 3.1.4 and weld group should be 3 + 1mm. for clearance 3.2, welding position: equatorial belt and upper and lower temperate longitudinal seam. 3.3. Welding material: CO2 gas protection, automatic welding adopts Phi 1.2 of Lincoln E712C welding wire, protection gas adopts CO2. 3.4 、 welding wire management: 3.4.1, welding in the welding wire, must have the factory certificate, the quality of the