塑胶及模具基础知识(二)（Basic knowledge of plastics and molds (two)）.docVIP

下载本文档

2
0
约2.57万字
约 28页
2017-09-05 发布于河南
举报
版权申诉

塑胶及模具基础知识(二)（Basic knowledge of plastics and molds (two)）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

塑胶及模具基础知识(二)（Basic knowledge of plastics and molds (two)）

塑胶及模具基础知识(二)（Basic knowledge of plastics and molds (two)） Basic knowledge of plastic and mold (two) for a.Txt line, will heat two people, will have a passion three of us are walking together, there will be. It is not cherish. Real girls arent perfect, perfect girls arent real. Take it easy, lose it, go with the flow and fight for it. 1. The cause of the weld mark produced by the product: 1-1 because the melting material part of the vanguard solidification in molten knottingmark confluence without causing strip. 1-2 because the air and the volatile material are closed There is residual release agent in the cavity of type 1-3. Two. Related knowledge: 2-1 uses a gate, did not make the products material confluence from 2 directions is not melting marks, in addition, if you want to avoid melting marks can only change the location of the gate of the melting knottingmark occurred in inconspicuous or looks pleasing to the eye position. 2-2 the pin on the mold (the hole in the product) usually has a weld mark. 2-3 because the air is closed to produce weld knot phenomenon is very much, so must make the air completely escape. 2-4 also useful for this method is to make the place where the weld mark occurs on the excess sheet of work in progress and then cut the sheet. 2-5 release agent too much of the molten material into the cavity part of the vanguard float, certainly will happen to sinter mark. Three. Solutions: 3-1, immediate: improve injection speed, improve mold temperature, improve the temperature of the cylinder, improve injection pressure. 3-2 short term: increase gas escape trough. 3-3 long term: change the position of the gate. A cause of the wave flow. 1-1 as the cooling begins, the cured resin enters the mold cavity Some of the mold temperature is too low Two. Related knowledge: 2 - 1 in the injection port, cooling the resin into the mold cavity while taking in in the semi solidified state, together with the die contact immediately curing, and then enter the depth