nsk轴承后缀代号说明（NSK bearing suffix code description）.doc

下载文档 降价啦

21
0
约8.83千字
约 14页
2017-09-07 发布于河南
举报
版权申诉
保障服务

nsk轴承后缀代号说明（NSK bearing suffix code description）.doc

1、本文档共14页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

nsk轴承后缀代号说明（NSK bearing suffix code description）

nsk轴承后缀代号说明（NSK bearing suffix code description） NS7S is the enclosed volume of oils and fats NSK designation.NS7 is NShilube grease S grease, is the enclosed volume (enclosed in the proportion is more than 35%). (1) internal structure A - Bearings with different designs and standards. A - angular contact ball bearings with a contact angle of 30 degrees. A5 - angular contact ball bearings with a contact angle of 25 degrees. B - angular contact ball bearings with a contact angle of 40 degrees. C - angular contact ball bearings with a contact angle of 15 degrees. C - tapered roller bearings with a contact angle of 20 degrees. D - tapered roller bearings with a contact angle of 28 degrees. C, CA (with solid brass cage), CD (with stamping cage), spherical roller bearing with high load. E -- high load cylindrical roller bearing. H - thrust roller bearing high load. J - tapered roller bearings of the outer raceway, the small end diameter, angle, outer ring width is consistent with the provisions of ISO. (2) materials G - ring, rolling is carburizing steel. H - ring, roll for stainless steel. (3) cage; M - copper alloy solid cage. T - synthetic resin cage. W - press holder. V - no cage. (4) sealing ring, dust cover Z, ZS - one with a steel cover. ZZ, ZZS -- dust cover for two side steel plate. D, DU - one side contact rubber ring. DD, DDU -- two faced contact rubber ring. V - one with a non-contact rubber ring. VV -- two side non-contact rubber sealing ring. (5) ring shape; K -- taper hole, taper 1:12. K30 -- taper hole, taper 1:30. E - there is a notch or oil hole in the ring. E4 - oil tank with oil holes on the outer ring. N -- outside outer diameter band stop groove. NR -- outer ring, outer band, stop groove, stop ring. (6) mating and lining DB - back to back pairing. DF - face to face installation. DT - tandem mounting. +K - outer ring lining. +L - inner ring lining. +KL - inner, outer ring with liner. H -- structural code for tight setting AH -- structural code for di