钣金机箱机柜通用检验标准（General inspection standard for sheet metal case and cabinet）.docVIP

下载本文档

16
0
约8.88千字
约 8页
2017-09-13 发布于河南
举报
版权申诉

钣金机箱机柜通用检验标准（General inspection standard for sheet metal case and cabinet）.doc

1、本文档共8页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

钣金机箱机柜通用检验标准（General inspection standard for sheet metal case and cabinet）

钣金机箱机柜通用检验标准（General inspection standard for sheet metal case and cabinet） General inspection standard for sheet metal case and cabinet This standard applies to the inspection and acceptance of sheet metal case and cabinet structure parts. It is an inductive and supplementary description of the basic and conventional technical requirements that are not in detail documented on the design document or need not be specifically pointed out. The requirements of this standard shall be identified with the design documents on technology together to carry out, except for what was beyond the standard precision terms proposed by the designers, quality inspection department for implementation, can also be performed on the basis for the designer to agree to this standard. The inspection and acceptance site shall be in the place of arrival of the goods designated by the manufacturer or Party A, and the results shall be consistent, and the final result shall be the final result. 2. citing standard enterprise standards Q/DMBM307-1997: inspection sampling rules. 3. cabinet 3.1 dimensional tolerances 3.2 form tolerance The sheet metal cabinet is not allowed to be visually inclined or partly twisted or twisted. The vertical angle of the frame column and base is less than 1.5mm. The upper surface of the base is taken as the benchmark and the inner side of the upper end of the column is taken as a measuring point. The parallel degree between the top frame and the base is less than 1mm. The detection points are the upper surface of the base and the lower surface of the top frame and are mutually reference. It can also be detected by measuring the length of the diagonal of the six sides, which shall not exceed 2.5mm. With the middle clapboard, the parallelism between the top frame and the base can be extended to 1.5mm, and the parallelism of the middle clapboard and the top frame or base is less than 1mm. The absolute value of the diagonal difference between the upper and lower bounding fr