模具设计专业术语（Terminology for die design）.docVIP

下载本文档

11
0
约 26页
2017-09-15 发布于河南
举报
版权申诉

模具设计专业术语（Terminology for die design）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

模具设计专业术语（Terminology for die design）

模具设计专业术语（Terminology for die design） Chinese and English comparison I. entering water: Gate Entry location: gate location Nozzle type: gate type Flood port: edge gate Nozzle: pin-point gate Nozzle size: gate size Rotary nozzle: switching runner/gate Sprue diameter: sprue diameter Two, runner: runner Hot runner: hot, runner, hot, manifold Hot runner: hot sprue/cold runner mouth cold DC: direct sprue gate sprue Round runner: round (full/half runner) Flow channel computer analysis: mold, flow, analysis Runner balance: runner balance Hot mouth: hot sprue Hot runner plate: hot manifold Heating tube: cartridge heater Probe: thermocouples Plug: connector plug Socket: connector socket Sealing / sealing: Seal Three, transport water: water line Throat plug: line, lpug Venturi: tube Plastic pipe: plastic tube Quick connector: jiffy, quick, connector, plug/socker Four, mold parts: mold components Three plate mold: 3-plate mold Second die: 2-plate mold Edge nail / edge: leader, pin/guide, pin Side Secretary / guide sleeve: bushing/guide bushing Naka Toshi: shoulder, guide, bushing Medium side L:guide pin Ejector plate: ejector, retainner, plate Pallet: support plate Screw: screw Pipe pin: dowel pin Mold opening: ply, bar, scot Internal die position: core/cavity inter-lock Thimble: ejector pin Cone: ejector, sleeve Ejector pin: ejector pin Push board: stripper plate Ha: movable, core, return, core, core, puller Button machine (nylon hook): Nylon latch lock Slanting top: lifter Base (frame): mold base Upper internal die: cavity insert Lower internal die: core insert Row position (slider): slide Insert: Insert Press seat / slant chicken: wedge Wear plate / oil plate: wedge, wear, plate Layering: plate Brace up: support pillar Sprue: sprue bushing Bezel: stop plate Positioning ring: locating ring Lock: latch Button chicken: parting lock set Putter: push bar Bolt screw: S.H.S.B Top: eracuretun Active arm: lever arm Splitter cone: spure sperader Shuiguchi Ji: Bush Garbage pin: stop pi