海信空调的故障代码（Hisense air-conditioning fault code）.docVIP

下载本文档

10
0
约2.55万字
约 34页
2017-09-15 发布于河南
举报
版权申诉

海信空调的故障代码（Hisense air-conditioning fault code）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

海信空调的故障代码（Hisense air-conditioning fault code）

海信空调的故障代码（Hisense air-conditioning fault code） E1 indoor temperature sensor is not good E2 indoor heat exchanger temperature sensor is not good E3 outdoor heat exchanger temperature sensor is not good E4 outdoor environmental temperature sensor is not good E5 over voltage protection E6 anti freeze protection E7 anti high temperature protection E8 outdoor ambient temperature is too low to protect E9 overcurrent protection Hisense air conditioning fault code KFR- (2318, 3218), GW/A, KF- (2318, 3218), GW/A, KFR-2501GW/D, KFR-3201GW, KFR-3301GW, KFR-3301GW/D, KFR-2501GW When the controller generates the protection, the sensor switch key is pressed, and the fault code is displayed on the display panel of the indoor machine, so as to be convenient for debugging and maintenance. When the air conditioner generates a fault code, the fault code cannot be cleared unless the power is off. The fault code is as follows: Fault name coding light emitting diode Efficient operation timing power supply Indoor temperature sensor failure 1 flashes Indoor heat transfer sensor fault 2 flashes Indoor heat intersection freeze 3 flashing Indoor heat, overheating, 4 flashes Instantaneous power 6 flashing Press current 7 flashing Fan block, turn 8 flashes Indoor machine E2PROM fault 13 flashing KF (R) -2510GW fault code If there is a fault in the circuit, the corresponding actions shall be shown as follows: except for fourth, fifth, the rest of the circuit will not stop. 1, if the indoor temperature sensor short-circuit or open fault, then the indicator light (yellow) flash two stop one; 2, if the indoor coil temperature sensor short circuit or open circuit fault, then the indicator light (yellow) flash three stop one; 3, if the outdoor Frost temperature sensor appears short circuit or open circuit fault, then the indicator light (yellow) flash seven stop one; 4, if the indoor fan due to failure to stop, (Holzer component pulse output to the chip), the indicator light (yellow) flash eight stop