摆线针轮减速机维护检修规程（Specification for maintenance and overhaul of cycloidal pin gear reducer）.docVIP

下载本文档

6
0
约1.63万字
约 25页
2017-09-23 发布于河南
举报
版权申诉

摆线针轮减速机维护检修规程（Specification for maintenance and overhaul of cycloidal pin gear reducer）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

摆线针轮减速机维护检修规程（Specification for maintenance and overhaul of cycloidal pin gear reducer）

摆线针轮减速机维护检修规程（Specification for maintenance and overhaul of cycloidal pin gear reducer） Specification for maintenance and overhaul of cycloidal pin gear reducer 1 General Provisions This regulation applies to the maintenance and overhaul of cycloidal pinwheel reducer (hereinafter referred to as reducer), and the maintenance and overhaul of cycloidal gear reducer can also be referred to execution. 2 inspection interval 2.1 overhaul category Repair and overhaul includes minor repairs, three. 2.2 inspection interval The period of inspection and maintenance is shown in Table 1 Table 1 h Overhaul category Minor repairs Repair Overhaul Maintenance interval Four thousand and three hundred Thirteen thousand Twenty-six thousand 3 overhaul content 3.1 minor repairs 3.1.1 cleaning body oil dirt and debris, replacement of lubricating oil or grease. 3.1.2 check and fasten bolts on each part. 3.1.3 check and eliminate the oil leakage in the joint surface and the seal. 3.2 medium maintenance 3.2.1 includes minor content 3.2.2 inspection, cleaning all parts of the body, wash oil dirt and debris. 3.2.3 remove lubricating oil and dredge oil circuit. 3.2.4 check, replace each department bearing (especially the arm bearing) and the skeleton rubber oil seal. 3.2.5 check, replace the dip pad, paper pad, oil resistant rubber pad and O type sealing ring. 3.2.6 check the pin sleeve, pin pin, pin pin and pin sleeve of the output shaft. 3.2.7 look for the positive coupling to ensure the coaxiality of the reduction shaft and the driven shaft. 3.3 overhaul 3.3.1 includes medium maintenance 3.3.2 inspection, repair or replacement of cycloid gear, needle tooth shell, output shaft and rotating arm (eccentric sleeve) and other key parts. 3.3.3 inspect, repair or change the base, fastening ring, isolating ring, cam and so on. 4 preparation before overhaul 4.1 technical preparation 4.1.1 manuals, drawings and related standards and other technical data. 4.1.2 records of operation, repair, defect, hidd