第六章塑料注射成型模具（The sixth chapter plastic injection mold）.docVIP

下载本文档

7
0
约 18页
2017-09-28 发布于河南
举报
版权申诉

第六章塑料注射成型模具（The sixth chapter plastic injection mold）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

第六章塑料注射成型模具（The sixth chapter plastic injection mold）

第六章塑料注射成型模具（The sixth chapter plastic injection mold） The sixth chapter plastic injection mold Fill in the blanks 1., according to the overall structural features of the mold, plastic injection mold can be divided into: (1); (2) (3); (4); (5); (6); (7); (8); (9) Other types. 2. basic parameters of injection molding machine mold parts,,, Sum. 3. the actual injection volume of the injection machine is best within the maximum injection quantity of the injection machine. 4. the clamping force of the injection machine must be greater than the product of the melt pressure in the cavity and the plastic part and the gating system. 5. the closed thickness of the injection mold to be designed must meet the following relationships:. If the die thickness is less than the minimum thickness permitted by the injection machine, the die can be adjusted to close the mold. 6. injection top set out device roughly,,, Other types. 7. the injection system of the injection mold has,,, Composition. 8., the main channel is generally located in the mold, it coincides with the injection machine. 9. injection molding runner design, from the heat transfer area considerations, thermosetting plastic should be used shunt channel; thermoplastic appropriate diversion channel. Considering the pressure loss, the diversion channel is the best; the diversion channel is easy to consider from the processing convenience. There are 10. and two types of cavity and shunt 11. when the cavity number is more affected by the die size limit, usually by unbalanced layout. Due to the diversion of different length can be used to achieve a balanced feed, this method can be achieved by. 12. when the injection model cavity and the flow channel are arranged, it is better to make the plastic parts and the distributary channel coincide with the center of the geometric center of the total projection area on the parting surface. 13. the type of gate can be divided,,, And six kinds. 14. gate cross section shapes are common and