成型主要不良分析及对策（Analysis and Countermeasures of main defects in molding）.docVIP

下载本文档

5
0
约2.23万字
约 27页
2017-09-29 发布于河南
举报
版权申诉

成型主要不良分析及对策（Analysis and Countermeasures of main defects in molding）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

成型主要不良分析及对策（Analysis and Countermeasures of main defects in molding）

成型主要不良分析及对策（Analysis and Countermeasures of main defects in molding） Analysis and Countermeasures of main defects in molding Analysis and Countermeasures of main defects in molding Purpose: The main reasons for the current bad products are analyzed and judged, in the molding machine, mold and raw materials to provide reference factors, so as to effectively control the bad production, reduce production costs. Content: 1 sores: (Silver Stripe) The surface of the finished product, with CATE as the center, there are a lot of silver streak, basically is produced along the flow direction of raw materials. This phenomenon occurs after the accumulation of many undesirable conditions, and sometimes it is difficult to seize the real reason. 1.1 of raw materials if there is water or other volatile components, not fully drying, it can produce a lot of silver on the surface. 1.2, raw materials accidentally mixed with other raw materials, it will form sores, and its shape is mica like or needle point, easy to cause sores with other causes, respectively. 1.3, raw materials or tubes are not clean, it is also prone to this situation. 1.4, the injection time is long, the initial injection into the mold cavity of the raw material temperature is low, the result of curing, so that volatile components will not rule out, especially for temperature sensitive raw materials, often occur in this situation. 1.5, if the mold temperature is low, then the raw material curing fast also easy to happen (1. 4) the condition that the volatile components are not expelled. 1.6 when the exhaust of the mold is bad, the gas will not easily be removed when the raw material enters, and it will cause sores. In this case, the top of the finished product will burn black. 1.7, if the mold is attached to moisture, then the raw material to bring the heat of evaporation, melting and melting of raw materials, forming a sore, protein, fog. 1.8 cold glue cold material or small nest material, injection, cooling the raw