十字路口红绿灯以及倒计时的显示（Intersections, traffic lights, and countdown displays）.doc

下载文档 降价啦

3
0
约7.1千字
约 14页
2017-10-07 发布于河南
举报
版权申诉
保障服务

十字路口红绿灯以及倒计时的显示（Intersections, traffic lights, and countdown displays）.doc

1、本文档共14页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

十字路口红绿灯以及倒计时的显示（Intersections, traffic lights, and countdown displays）

十字路口红绿灯以及倒计时的显示（Intersections, traffic lights, and countdown displays） ORG 0000H; main program entry address LJMP START ORG 0003H; external interrupt 0 entry address LJMP INT_0; emergency vehicle interrupt service routine ORG 000BH; timer T0 entry address LJMP INTER; timer T0 interrupt service routine ORG 0013H LJMP INT_1 START:, MOV, R2, #100; the number of timer T0 overflows MOV, TMOD, #01H; timer T0 works in mode 1 MOV, TL0, #0F0H; assign the initial value to the timer T0 MOV, TH0, #0D8H MOV, IE, #87H; open interrupts, and allow timer T0 and external interrupts 0, 1 to generate interrupts SETB IT0; external interrupt 0 is the falling edge trigger SETB IT1 SETB PT0; setting the interrupt priority level of timer 0 is high MOV, R0, #60; status 1 digital tube countdown initial value BB1:MOV P0, #81H; 1: East roadway light, and green light SETB P2.0; the red light on the East-West sidewalk and the green light on the North South walkway CLR P2.1 SETB P2.3 CLR P2.2 SETB TR0; open timer T0, same as below LCALL DAOJISHI; call the digital tube countdown display subroutine, the same below CJNE, R0, #0FFH, BB1; determine whether the countdown to status 1 is completed, not to BB1, but to continue CLR TR0; after the countdown completes, turn off the timer T0 MOV, R0, #5; status 2 digital tube countdown initial value SETB TR0 AA2:ACALL DAOJISHI CJNE R2, #50, EE2; to determine whether or not to overflow 50 times, that is, to determine whether to 0.5 seconds, not jump to EE2, is to continue to perform MOV, P0, #42H; overflow 50 times, then each intersection yellow light EE2:CJNE, R2, #1, FF2; determine whether the overflow 99 times, that is, to determine whether to 1 second, not jump to FF2, is to continue to perform MOV, P0, #00H; overflow 99 times, each intersection yellow lights out FF2:CJNE, R0, #0FFH, AA2; determine whether the state 2 countdown is completed, not skip to AA2, or continue CLR TR0 MOV, R0, #80; status 3 digital tube countdown initial value BB3:MOV P0, #24H; 3: