如何安装双硬盘及硬盘的常见故障和自我检修（How to install common faults and self repair of double hard disk and hard disk drive）.docVIP

下载本文档

6
0
约1.07万字
约 10页
2017-10-07 发布于河南
举报
版权申诉

如何安装双硬盘及硬盘的常见故障和自我检修（How to install common faults and self repair of double hard disk and hard disk drive）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

如何安装双硬盘及硬盘的常见故障和自我检修（How to install common faults and self repair of double hard disk and hard disk drive）

如何安装双硬盘及硬盘的常见故障和自我检修（How to install common faults and self repair of double hard disk and hard disk drive） 1. set by hard disk jumper All IDE devices, including the hard disk, use a set of jumpers to determine the master and slave state after installation. The hard disk jumper is mostly located between the power connection seat and the data line connection socket (also has on the circuit board), usually consists of 3 sets (6 or 7) needle or 4 sets (8 or 9) needle, plus one or two jumper cap. In addition, the main disk (Master), the slave disk (Slave) and the jumper method selected by the cable (Cableselect) must also be printed on the front or the back of the hard disk. Jumper method and various types of hard disk labeled instructions are similar, such as jumper quantum hard disk usually has 9 needle 4 groups, one of which is called Key, so that the user is used to locate the correct identification of jumper position. 2. by hard disk jumper and 40 core special hard disk line to determine The setting of the main disk and the slave disk is that the hard disk jumper is first arranged after the cable is selected effectively, and then the main disk and the slave disk are connected to the corresponding hard disk plug on the basis of the need. The settings of the main disk and disk status depend on the connecting plug of the hard disk and hard disk. Usually, the disk that connects the middle part of the hard disk is the main disk, and the disk attached to the plug at the end of the hard disk is the disk. When this method is used to set the master and slave disks, the jumper of all the IDE interface devices (including CD-ROM drives) that are connected to the same hard disk must be located at the location of the cable selection. Can determine the disk master, from disk state, 40 core hard disk is special. The manufacturing method is to cut the twenty-eighth lines of an ordinary 40 core hard disk (from first red lines or other markings) at the position between two hard disk p