立式加工中心的理和实习培训,（Training and practice of vertical machining center,）.docVIP

下载本文档

2
0
约1.16万字
约 12页
2017-10-07 发布于河南
举报
版权申诉

立式加工中心的理和实习培训,（Training and practice of vertical machining center,）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

立式加工中心的理和实习培训,（Training and practice of vertical machining center,）

立式加工中心的理和实习培训,（Training and practice of vertical machining center,） The operator must be familiar with machining center operation manual and machine performance, and after the vertical machining center and training, through the exam to obtain certificate, have the qualification of operation of vertical machining center. First, before the boot ready: 1. machine tools in each boot or machine after urgent stop reset, first of all back to the machine tool reference zero (ie zero), so that the machine tool for its subsequent operation has a benchmark position. 2. clamping workpiece: The 3. clamping workpiece before cleaning the surface, not sticky oil, scrap iron and dust, and with a file (or stone) to remove the burr on the surface of the workpiece. 4., clamping the use of high-speed rail must be grinding through the grinding of the surface, so that it smooth and smooth. The iron and nut must be strong and reliable to clamp the workpiece. Some small workpieces which are difficult to clamp can be clamped directly on the vise. 5. machine tool working platform should be clean, without iron filings, dust, oil pollution. 6. pads are usually placed at the four corners of the work piece. The workpiece with a long span should be placed in the middle. 7. according to the size of drawing, use drawing ruler to check whether the length, width and height of the workpiece are qualified. 8., when clamping workpiece, according to the programming instruction book installation way, we should consider avoiding the processing parts and the tool head may touch the fixture in the process. 9. after the workpiece is placed on the pad, it is necessary to pull the surface of the workpiece according to the requirements of the drawing. The workpiece length direction error is less than 0.02mm, and the horizontal error of the top surface X and Y is less than 0.05mm. Check the verticality of the workpiece which has been grinded on six sides. 10. after the workpiece has been pulled out, the nut must b