光钎放大器说明书（Specification for optical drill amplifier）.docVIP

下载本文档

11
0
约1.18万字
约 15页
2017-10-05 发布于河南
举报
版权申诉

光钎放大器说明书（Specification for optical drill amplifier）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

光钎放大器说明书（Specification for optical drill amplifier）

光钎放大器说明书（Specification for optical drill amplifier） Two-point calibration In this mode, the PV used will be the average of the two sensing values obtained with or without artifacts. 1 press the SET (settings) button before placing any artifacts in front of the fiber module. 2 place a workpiece in front of the fiber module and press the SET (settings) button. If the sensitivity is not enough space, in after the calibration, ____ will flash for about 2 seconds. Even on In this case, the setting value will still be stored in memory. Percentage (%) calibration The calibration method can be set according to the percentage of the received light intensity when the sensitivity is set. For example, if the target value is set to -10P, then the set value is determined when the SET (setting) button is pressed The received light intensity is 10% lower. 1 select the sensitivity setting method (page second, fourth), select% calibration, and then set the target value for calibration. 2 press the SET (setting) button for reference to the desired light intensity (usually without the use of the workpiece). No other calibration (sensitivity setting) can be used when using% calibration. * use FS-V31C (P) /32C (P) to periodically perform external calibration from PLC or other devices, even if With slight sensitivity, the gap can also be stably detected. Set maximum sensitivity If it is a reflective workpiece, the sensitivity is set without placing the workpiece; if the light transmissive workpiece is used, then Setting up the workpiece In the status shown above, press the SET (settings) button for 3 seconds. (SET) blinks when the release button is used. ) When setting the sensitivity, the setting value should be slightly higher than the received light intensity Fully automatic calibration In this mode, PV sets the average value of the maximum and minimum associated values in the given time. The die is used Type detects moving workpieces. 1 hold the SET (settings) button for at least 3 se