- 1、本文档共20页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
- 5、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
- 6、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们。
- 7、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 8、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
基于子模组工况分析的模块化多电平储能系统开路故障诊断方法
基于子模组工况分析的模块化多电平储能系统开路故障诊断方法
毕恺韬 安群涛 孙东阳 段建东 孙力
哈尔滨工业大学电气工程与自动化学院
X
关注成功!
加关注后您将方便地在 我的关注中得到本文献的被引频次变化的通知!
新浪微博
腾讯微博
人人网
开心网
豆瓣网
网易微博
摘????要:
储能系统中直流变换器的安全性及可靠性直接关系到系统是否正常运行。通过对模块化多电平直流变换器中半桥子模组故障运行工况的分析, 提出一种在超级电容模组宽工作电压范围下的快速开路故障诊断方法。该方法根据正常及故障时半桥子模组下桥臂承受电压的不同, 利用简单的硬件检测电路以及基于FPGA的诊断算法实现快速开路故障诊断。硬件检测电路能够实时对半桥子模组运行工况进行检测, FPGA中故障诊断算法则利用检测结果并结合驱动信号在短时间内完成故障诊断。详细给出所提方法的设计原理以及关键参数的选取原则。该方法避免了复杂的数学运算, 容易实现。最后, 通过搭建小功率模块化多电平储能系统对所提方法进行了验证。
关键词:
超级电容储能系统; 模块化多电平直流变换器; 开路故障诊断; 快速诊断; 半桥子模组;
作者简介:毕恺韬, 男, 1989年生, 博士研究生, 研究方向为大功率储能系统以及电力电子变换器故障诊断等。E-mail:1039351556@
作者简介:安群涛, 男, 1984年生, 博士, 副教授, 研究方向为电机控制以及新能源发电技术。E-mail:anquntao@163.com.
收稿日期:2016-08-08
基金:国家自然科学基金 51277040
Modular Multilevel Energy Stroage System Open Circuit Diagnostic Method Based on Sub-Module Operation Analysis
Bi Kaitao An Quntao Sun Dongyang Duan Jiandong Sun Li
School of Electrical Engineering and Automaton Harbin Institute of Technology;
Abstract:
These curity and reliability of DC converter in energy storage system are directly related to the normal operation of the system. By the analysis on fault operation conditions of half bridge sub-module in modular multilevel DC-DC converter (MMDDC) , this paper proposes a fast-open circuit diagnostic method, which can be used under a wide super capacitor voltage range. According to different voltages endured by the lower arm under normal and fault conditions, a simple hardware detection circuit and a concise diagnosis algorithm built in FPGA are hence employed. The detection circuit is responsible for detecting the operating conditions of sub-module in real time, while the diagnosis algorithm accomplishes the final diagnosis using detection results and drives signals in a short time. The design principle of the proposed method and the selection principle of the key parameters are provided in detail. The proposed method avoids complex mathematical calculations and is easy to be implemented. Finally, the proposed diagnosti
文档评论(0)