十字路口交通灯控制系统报告.docxVIP

十字路口交通灯控制系统161230229 张洪刚目录十字路口交通灯控制系统1需求分析1体系结构设计1硬件设计1软件设计 – 流程图2程序代码2仿真调试6需求分析设置一个交通信号控制系统，同时控制两个方向的红黄绿灯时间，时间显示位数为3位。体系结构设计硬件设计软件设计 – 流程图程序代码#include LPC213x.h // 红绿灯时间满足下面两个等式// RedSN = GreenEW + YellowEW// RedEW = GreenSN + YellowSN/*#defineGreenEW20#defineYellowEW4#defineRedEW31#defineGreenSN25#defineYellowSN6#defineRedSN24*/#defineGreenEW100#defineYellowEW4#defineRedEW111#defineGreenSN105#defineYellowSN6#defineRedSN104unsigned char led_table[] = {0x00,0x01,0x02,0x03,0x04,0x05,0x06,0x07,0x08,0x09,};unsigned char flag = 0;int showNumEW[3] = { 0 };int showNumSN[3] = { 0 };int greenEW = GreenEW, yellowEW = YellowEW, redEW = RedEW;int greenSN = GreenSN, yellowSN = YellowSN, redSN = RedSN;void show_value_set( unsigned int valueEW, unsigned int valueSN ){showNumEW[0] = valueEW % 10;showNumEW[1] = valueEW % 100 / 10;showNumEW[2] = valueEW % 1000 / 100;showNumSN[0] = valueSN % 10;showNumSN[1] = valueSN % 100 / 10;showNumSN[2] = valueSN % 1000 / 100;}void disp( unsigned char id1, unsigned char numHigh, unsigned char numMid, unsigned char numLow ){if( id1 == 0 ){IO0SET |= led_table[numHigh];//输出高位数据IO0SET |= led_table[numMid] 4;//输出低位数据IO0SET |= led_table[numLow] 8;//输出低位数据}else{IO1SET |= led_table[numHigh] 16;//输出高位数据IO1SET |= led_table[numMid] 20;//输出高位数据IO1SET |= led_table[numLow] 24;//输出低位数据}}void flush_led( unsigned char flag )//闪烁LED{IO0CLR |= 0xfff;// 数码管IO1CLR |= 0xfff 16;IO0SET |= (0x7f 21);// 关闭所有灯if( flag = 0 flag GreenEW ){IO0CLR |= (0x44 21); // 灯亮show_value_set( greenEW--, redSN-- );}else if( flag = GreenEW flag RedSN ){IO0CLR |= (0x24 21); // 灯亮show_value_set( yellowEW--, redSN-- );}else if( flag = RedSN flag (RedSN+GreenSN) ) {IO0CLR |= (0x11 21); // 灯亮show_value_set( redEW--, greenSN-- );}else{IO0CLR |= (0x12 21); // 灯亮show_value_set( redEW--, yellowSN-- );}disp( 2, showNumEW[2], showNumEW[1], showNumEW[0] );disp( 0, showNumSN[2], showNumSN[1], showNumSN[0] );}void __irq IRQ_Timr0(void){flag = ++flag=(RedSN+RedEW+1) ? 0 : flag;if( flag =