- 1、本文档共18页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
电气控制技术课程设计说明书
电镀车间专用行车PLC控制系统设计2011-10-28
摘 要
本文以电镀自动生产线控制系统设计为研究对象,以其电镀专用行车为控制对象,对其电镀的工艺要求和控制要求进行了分析,采用理论研究的方法,设计了一套基于PLC的电镀车间专用行车自动控制系统。本系统选用三菱FX2N-64MR-001型号的PLC来进行控制,通过PLC输出信号接触器的触点动作,来控制三台异步电动机的运行,从而实现对行车的水平运动和吊钩的垂直运动的控制,考虑到电镀、上升、下降等运动时行车和吊钩需要准确停位。在程序设计时为了便于对设备进行调整和检修,设计了手动程序以实现对行车和吊钩的点动控制,对于自动控制程序的设计,其工作过程是典型的顺序控制,采用步进指令能很好的实现对其控制。通过软件仿真可以看出所设计的控制系统很好的实现了电镀的工艺要求和控制要求,可以方便完成自动和手动之间的切换,体现出
PLC控制系统具有调试方便、适应性强的优点。
关键字:电镀行车;可编程控制器;梯形图
ABSTRACT
The electroplating automatic production line to control system design to study, with its specialized operations to control traffic. the electroplating technology and control of the claim was analysed and the theory of the research methods, design a web based on the plc electroplated impression of the special traffic control system; The system for mitsubishi fx2n - 64mr -001 kind of the plc to control, the output signal of the plc contacts with some action to control motor three asynchronous operation, the level of the motion and the hook vertical motions of the operations, rising and falling, the motion and the hook to the right stop. in programming, to facilitate the adjustment of equipment and design a manual procedures for the implementation and hook at the control, the automatic control of the design, it is typical of the order of control and use the step into the instructions to the very good with the controls. Through software simulations can see that the system of the electroplating technology and control, you can easily finish automatic and manual switch between that of the plc control system for the adaptable.
Key words:the electroplating ;programmable logic control;terraced figure
目 录
1 绪 论……………………………………………………………………………3
1.1 电镀生产线简介……………………………………………………………3
1.2 电镀车间行车专用PLC控制系统设计内容………………………………3
1.2.1 设备基本情况………………………………………………………3
1.2.2 拖动系统……………………………………………………………4
1.3 电镀车间行车专用PLC控制系统设计要求………………………………4
1.4 可编程控制器简述………………………………………………………4
2 控制系统总体方案及系统硬件设计……………………………………………5
2.1 电镀车间专用行车PLC控制
您可能关注的文档
- 2000m3球罐设计毕业设计说明资料.doc
- 2010高教社杯全国大学生数学建模大赛A题论文.doc
- 2012届本科毕业论文设计抽查情况汇报.doc
- 2012年数学建模国赛一等奖论文A1614.doc
- 2013毕业设计小游戏之五子棋的MFC实现.doc
- 20142015MATLAB论文基本结构及格式要求陈宗帆李程月李庆琳.doc
- 2015届本科毕业论文任务资料和开题报告模版.doc
- 2016年最新二级心理咨询师论文要求及范文.doc
- 2017年工程造价毕业论文范文 .doc
- 2017年本科局域网文件共享与检索系统设计毕业论文.doc
- 第十一章 电流和电路专题特训二 实物图与电路图的互画 教学设计 2024-2025学年鲁科版物理九年级上册.docx
- 人教版七年级上册信息技术6.3加工音频素材 教学设计.docx
- 5.1自然地理环境的整体性 说课教案 (1).docx
- 4.1 夯实法治基础 教学设计-2023-2024学年统编版九年级道德与法治上册.docx
- 3.1 光的色彩 颜色 电子教案 2023-2024学年苏科版为了八年级上学期.docx
- 小学体育与健康 四年级下册健康教育 教案.docx
- 2024-2025学年初中数学九年级下册北京课改版(2024)教学设计合集.docx
- 2024-2025学年初中科学七年级下册浙教版(2024)教学设计合集.docx
- 2024-2025学年小学信息技术(信息科技)六年级下册浙摄影版(2013)教学设计合集.docx
- 2024-2025学年小学美术二年级下册人美版(常锐伦、欧京海)教学设计合集.docx
文档评论(0)