刀具刃磨中心车刀夹持模块设计与建模论文推荐.docVIP

刀具刃磨中心车刀夹持模块设计与建模 [摘要] 本文主要阐述了车刀等常用刀具的种类及其分类方法；建立了常用车刀的三维零件模型；并确定了车刀刃磨的参数；对车刀角度及车刀角度对切削加工的影响作了研究和分析；详细阐述了刀具各个角度的刃磨方法；研究车刀不同位姿，建立其数学模型并设计相应夹具。 [关键词]车刀角度 刃磨参数 三维建模 数学模型 刃磨装置 Knives cutting tool clamping module design center with modeling (Grade07,Class4,Major Mechanical design and manufacture of extremely automation ，Mechanical Engineering College Dept.，Shaanxi University of Technology，Hanzhong 723003，Shaanxi ) Tutor：Zhang Junfeng Abstract：This paper mainly expounds the commonly used tools such as tool type and classification method; Established three-dimensional parts model cutting tool; The cutting tool to determine the parameters; On turning Angle and turning Angle to cutting the influence of the research and analysis; Explains in detail the method of each Angle cutting tools; Research tool, establish its position and pose different mathematical model and design corresponding fixture. Key words：Lathe tool Turning Angle Gear parameters Three dimensional modeling Mathematical model Fixture design 目 录 TOC \o 1-3 \h \u HYPERLINK \l _Toc2925 引 言 PAGEREF _Toc2925 1 HYPERLINK \l _Toc6583 1. 车刀刃磨参数分析 PAGEREF _Toc6583 2 HYPERLINK \l _Toc7514 1.1车刀基础知识 PAGEREF _Toc7514 2 HYPERLINK \l _Toc13150 1.1.1 车刀的组成 PAGEREF _Toc13150 2 HYPERLINK \l _Toc4085 1.1.2 车刀的角度和主要作用 PAGEREF _Toc4085 2 HYPERLINK \l _Toc13078 1.2常用车刀的种类和用途 PAGEREF _Toc13078 3 HYPERLINK \l _Toc29451 1.2.1普通车刀的结构分类 PAGEREF _Toc29451 3 HYPERLINK \l _Toc18642 1.3 车刀各个角度对切削的影响 PAGEREF _Toc18642 5 HYPERLINK \l _Toc4474 1.3.1前角的功用及选择 PAGEREF _Toc4474 5 HYPERLINK \l _Toc30905 1.3.2 后角功用及选择 PAGEREF _Toc30905 6 HYPERLINK \l _Toc25035 1.3.3 主偏角的功用及选择 PAGEREF _Toc25035 7 HYPERLINK \l _Toc25304 1.3.4 副偏角的功用及选择 PAGEREF _Toc25304 8 HYPERLINK \l _Toc8402 1.3.5 刃倾角的功用及选择 PAGEREF _Toc8402 8 HYPERLINK \l _Toc432 1.4不同车刀在不同切削条件下的刃磨参数 PAGEREF _Toc432 9 HYPERLINK \l _Toc13351 1.4.1外圆车刀几何参数的参考值 PAGEREF _Toc13351 9 HYPERLINK \l _Toc27970 1.4.2常用切断刀的几何参数 PAGEREF _Toc27970 11 HYPERLINK \l _T