泌阳县城污水厂工艺设计毕业设计.docx

摘 要本次毕业设计的题目为泌阳县城市污水厂工艺设计，主要任务是完成该地区的污水厂设计。 该污水厂的设计规模：30000m3/d，本工程设计进水水质为：BOD5=200mg/L， COD=420mg/L，SS=300mg/L，NH3-N=20mg/L，TN=40mg/L，TP=3.0mg/L。根据国家有关规定，二级城市污水处理厂出水应执行《城镇污水处理厂污染物排放标准》（GB18918-2002）一级B标准。则本处理厂出水水质标准为： BOD5≤20mg/L， COD≤60mg/L，SS≤20mg/L，NH3-N≤8mg/L，PO4-P≤1mg/L。本文根据其进水水质，水量及出水情况，分析比较了各种污水处理工艺，确定了该污水处理厂采用A/A/O工艺，产生的污泥经浓缩，脱水后外运。主要设计内容为：污水处理工艺选择及各工艺单元的设计：污泥处理工艺设计：污水处理厂的平面及高程布置。 关键词：污水处理 A/A/O工艺 构筑物 工程 设计 AbstractThe graduation design topic for the Miyang sewage treatment plant process design. The main task is to complete a the region of the sewage processing design. Miyang sewage treatment plant the construction scale: 30000 m3/d; The original water: CODCr: 420mg/L, BOD5:200mg/L; SS: 300mg/L; NH3-N: 20mg/L; TN:40mg/L; TP:3.0mg/L for handling the water quality to achieve after the country the urban sewage treatment plant emissions standards (GB18918-2002) level 1B standard requirements: CODCrthan60 mg/L, more than 20mg/L BOD5, SS than 20mg/L, NH3-N than 8mg/L, TP than 1.0 mg/L. In this paper, according to the feed water quality, water and water situation, analyses and compares the all kinds of wastewater treatment process, determine the sewage treatment plant using the A/A/O process, the sludge produced by the enrichment, sinotrans after dehydration. The main design content includes: choosing the wastewater treatment process and the process of design unit ; The sludge treatment process design, (including process flow and the determination of the monomer structures design); Sewage treatment plants the plane and elevation layout . KEY WORDS: wastewater Treatment, A/A/O process, construct building,design, engineering 目 录1. 概 述11.1 项目基本情况11.2 设计依据与基础资料11.3 设计采用的主要设计规范与标准11.3.1 水质标准11.3.2 勘察、设计规范11.3.3 施工和验收规范31.3.4 主要政策法律41.4 设计原则41.5 设计范围52. 总体设计及厂址选择62.1项目名称62.2工程概述62.3基本设计参数62.3.1气象资料62.3.2设计规模62.3.3设计进出水水质62.3.4去除率72.4厂址选择83. 污水处理厂工艺选择93.1 污水处理工艺选择原则93.2 污水处理工艺比选93.2.1 按空间分割的连续流活性污泥法93.2.2 按时间分割的间歇式活性污泥法133.2.3 生物膜法143.2.4