- 1、本文档共4页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
超高温下石墨弹性极限的拐点及其孔隙率影响-硅酸盐学报
第 46 卷第 4 期 硅 酸 盐 学 报 Vol. 46 ,No. 4
2 0 1 8 年 4 月 JOURNAL OF THE CHINESE CERAMIC SOCIETY April ,2018
DOI :10.14062/j.issn.0454-5648.2018.04.12
超高温下石墨弹性极限的拐点及其孔隙率影响
刘 钊,包亦望,万德田
(绿色建筑材料国家重点实验室,中国建筑材料科学研究总院,北京 100024)
摘 要:石墨的杨氏模量随温度升高而增大并在超高温下出现拐点。该推测至今未得到有效验证,特别是石墨的弹性极限峰
值及其影响因素都是未知的。尽管三点弯曲法能够简便快捷地评价陶瓷的杨氏模量,但该方法在超高温下由于无法精确测量
挠度而不再适用。本研究旨在改进三点弯曲法的基础上来测量石墨直至 2 000 ℃的杨氏模量,并探讨孔隙率对石墨超高温弹
性极限的影响。结果表明:石墨随温度上升的模量的拐点温度在 1 700~1 800 ℃范围内;孔隙率为 16.5%的石墨,在 1 500 ℃
以上具有最佳的杨氏模量,该值也反映了石墨在超高温下所具有的弹性极限。
关键词:弹性极限;杨氏模量;超高温;石墨;孔隙率
中图分类号:TB321 文献标志码:A 文章编号:0454–5648(2018)04–0537–04
网络出版时间: 网络出版地址:
Inflection and its porosity effect on elastic limit of graphite at ultra-high temperature
LIU Zhao , BAO Yiwang, WAN Detian
(State Key Laboratory of Green Building Materials, China Building Materials Academy, Beijing 100024, China)
Abstract: It was supposed that the Young’s modulus of the isostatically pressed graphite could go up with the increase of temperature
until a critical value. This conjecture has not been verified yet, especially for the peak value of graphite elastic limit and the
corresponding affecting factors. Although three-point bending method is effective to estimate the Young’s modulus of ceramics, it is
unavailable to be used at ultra-high temperature due to the difficulties of obtaining a precise deflection at such high temperature. This
paper was to measure the varying modulus of graphite at different temperatures (up to 2 000 °C) by the modified three-point method
and investigate the effect of porosity
文档评论(0)