西南交通大学土木工程制图三C制图源程序.docVIP

16-1 CRect rc; GetCI i entRect(rc); pDC-SetMapMode(7); pDC-SetW i ndowExt(500, 500); pDC-SetV i ewportExt(rc. r i ght, -rc. bottom); pDC-SetW i ndowOrg(0, 0); pDC-SetVi ewportOrg (rc. r i ght/2, rc. bottom/2); POINT pp[3]二{-240, 0, 240. 0, 0, 120 }; pDC-Po I ygon (pp, 3); pDC-LineTo(-80, 80); pDC-LineTo(-80, 0); pDC-LineTo(-160,40); pDC-L i neTo (-160, 0); pDC-MoveTo (0, 0); pDC-LineTo(80,80); pDC-Li neTo (80,0); pDC-LineTo(160,40); pDC-Li neTo (160,0); pDC-MoveTo (0, 0); pDC-LineTo(0, 120); 16-2 CRect rc; GetCIientRect(rc); pDC-SetMapMode (7); pDC-SetW i ndowExt (500,500); pDC-SetV i ewportExt(rc. r i ght, -rc. bottom); pDC~SetWi ndowOrg(0, 0); pDC-SetViewportOrg(rc. r i ght/6, rc. bottom/2); int x[14], y [14], z[14], i =0, n=0, m=250; CPen *pen1, *pen2; for(i=0;i=14; i++) {x[i]=290-10*i; y[i]=80-10*i; z[i]=310+10*i; pen1=new CPen (0, 1, RGB (n, m, n)); pen2二pDC-SeIectObject (pen1); pDC-Arc (x [ i ] J 00, z [ i ], y [ i ], z [ i ], 100, z [ i ], 100); n=n+15; m=m-15;} pDC-SeI ectObject (pen2); de I ete peril ; 16-3 #incIude math, h CRect rc; GetCI i entRect(rc); pDC-SetMapMode(7); pDC-SetWindowExt(500, 500); pDC~SetV i ewportExt(rc. r i ght, -rc. bottom); pDC-SetW i ndowOrg(0, 0); pDC~SetViewport0rg(rc. r i ght/2, rc. bottom/2); double x[11] = {0}, y[11] = {0}; double t=0, a二0. 2, r2=38. 2; int i, r1=100; for (i=0;i=11;i+=2) { x [ i ]=r1 *s i n (t*3. 1416); y[i] =r1*cos(t*3. 1416); t=t+0. 4;} for(i=1;i〈二9;i+=2) { x[i] =r2*s in (a*3. 1416); y[i]=r2*cos(a*3.1416); a二a+0. 4;} pDC-MoveTo((int)x[0], (int)y[0]); for(i=0;i=10;i++) pDC-LineTo((int)x[i], (int)y[i]); for(i=0;i=10;i++) {pDC-MoveTo (0, 0); pDC-LineTo((int)x[i], (int)y[i]); 16-4 CRect rc; GetCI i entRect(rc); pDC-SetMapMode(7); pDC-SetW i ndowExt(200, 200); pDC-SetV i ewportExt(rc. r i ght, -rc. bottom); pDC-SetW i ndowOrg(0, 0); pDC-SetVi ewportOrg(rc. r i ght/2, rc. bottom*2/3); CPen *p01, *p02; POINT pt[4]二{0,0, 10,0, 10,100, 0, 100}; POINT pb[10] = {90,0, 80,10, 20, 10, 20,70, 10,80, 0,80, -10, 70, -10, 10,