储罐安装抗风载荷计算Wind Load Calculation Sheet.docVIP

储罐安装抗风载荷计算 Wind Load Calculation Sheet 1、Wind load：W0=800Pa （Refer to CA-8430-0800-0001） 风载荷：W0=800Pa （参见CA-8430-0800-0001） Standard value of wind load:W=?z μz μs W0 Herein, ?z refers to wind vibrating factor ，?z=1； μz refers to wind pressure height factor， μz=1.38*(H/10)1/4 =1.38*(22/10)1/4 =1.681； μs refers to wind load shape factor，μs=1.5； W0 refers to standard value of wind pressure W0=800Pa Therefore， W=1×1.681×1.5×800=2018 Pa 风载荷标准值为：W=?z μz μs W0 其中：?z 为风振系数，取?z=1； μz 为风压高度系数，取μz==1.38*(H/10)1/4 =1.642； μs 为风载体型系数，取μs=0.8； W0 为风压标准值 W0=800Pa 所以， W=1×1.681×1.5×800=2018 Pa 2、Calculating conditions 计算条件： 1） The inclination between the steel cable and ground as well as tensile stress is biggest when the last course shell plate is installed and after clamps is fixed. 安装最后一圈壁板，工卡具固定完毕，此时钢丝绳与地面夹角最大，受拉应力也 最大； 2） For single course shell plate, semi-circle area is supposed to support the front wind load. 按单圈壁板，半圆范围承受正面风载荷； 3） （In the semi-circle area） steel cables are located in six points equally. （半圆范围内）用钢丝绳封6 个位置均布； 4） One steel cable is set for each point. 每个位置用单根钢丝绳； 5） The variable of steel cables(钢丝绳参数：): Steel cable:6×37 6X37 钢丝绳 Diameter: f 28.0mm 直径 f 28.0mm Tensile intensity: 170kg /mm2 钢丝绳公称抗拉强度为 170 公斤 /毫米2 Total section area: A0=85.39mm2 钢丝总断面面积 A0=291.52mm2 Therefore, the total breakage tensile strength is more than 50050kg. See SYB-4112-80 Hoisting Operating Procedure. Detailed in Appendix. 因此，钢丝绳破断拉力总和不少于50050 公斤 见 SYB-4112-80 《起重工操作规程》。具体的见附页。 3、Calculation on the tensile stress of the steel cable 钢丝绳抗拉强度计算 1） Force analysis 受力分析 2） Front cross-section area to support wind load: A=78*2.48=193.44m2 承受风载荷正截面面积：A=78*2.48=193.44m2; 3) Pressure produced in the front cross-section area: F=193.44*800=154752N 正截面上产生的压力： F=193.44*2018=390363N 4) Considering the maximum pull force of the front of steel cables and the less force in the two sides, the load of one steel cable is: F1=390363/6= 65060N 考虑正面钢丝绳受拉力最大，而两侧受力减弱。因此，单根钢丝绳承担的风载荷为： F1=390363/6= 65060N 5) Pul