冷拔材两辊滚光矫直机分析与设计-机械工程专业论文.docxVIP

重庆大学硕士学位论文 重庆大学硕士学位论文 荚交{蓠要 ABS董鼗轰CT Study and analyze importation KIESERLING heavy-duty wire turning line DDKSR 20／40 of Germany that is in cold-drawing workshop,No，4 Plant Changcheng Special Steel Co。We have designed a heavy-duty wire straight line successfully with reversing engineering design．In this paper,study hi曲precision wire-rod two—roll straightening／polishing machine and it analyze the principle,miler-curve,relation between the rolter-characteristic and installation angle of two—roll straightening／ polishing machine．The standard equations of the roller-curve have founded with computer program．Qualitative analyzes straightening／polishing principle ofroller．curve BO astoprovideaccuratereliahletheoryfoundationformakingroller-cm,e， In this paper,the atl transmission system principle and structure parameter are calculated，test and verify,studied analysis completely．The motor,decelerator,shaft coupling and bearing are designed and made in China etc．According to site actual siRmfion。partial s礅lohlf{嚣Rre遮pmved in order to make it become simple convenient practical and con嘶bute to repair operation for straightening machine．The intensity, rigidity and longevity of the roller-axle,mechanism，bearing and others are calculated and analyzed．The two-mli straightening machine has designed sucoessful黟to come up to world standard． Keywords：2-roll straightening／polishlng machine,computer generator, reverse engineering design,roller-curve，transmission system, meehanies analysis 珏 重痰大学硕七学位论文 重痰大学硕七学位论文 1绪论 1绪论 1．1项目概述 长城特殊钢公霹燕强钢厂冷拔分厂是辕撼冷会部(86)冶诗字第008鼍文{牛(长 城诵厂复合小鍪!车溺玲拔工段移魄改建任务书)于“七五”灏闻规划设计并实施韵 项目，建厂后冷拔分厂规模为占地70亩，年产各种冷加工材15000吨，蕻中包括 经委(86)54号文件和冶金部(86)冶军字第109号文件批准建设的军用商精发银亮钢 生产线豹1200嚏锾嶷钢毒手眨 冷拔分厂竣工艏，由于种种原因，许多配套设施没有完善，不能达到设计能 力的要求。随着我豳市场经济的发展，原设计的产品方案融不适应市场需要，如 汽车工渡、摩托车行救呈强劲发鼹势头，钢材的灏产纯日盏紧追，规辏由昏9-14mm 囱审5-28mm延伸，仅汽车内燃枫溺汽瓣钢的数蓬就达3万魄，而当时禹产化率仅 为30％。近年来，冷拔分厂用剥皮加工工艺生产的剥皮银亮钢深受用户好评，需 求量大增，远远超过现有剥皮机的能力。于是第四钢厂决定新增一条剥皮机生产 线(幸5-20ram)。霹荚缀姨德国雩|逡豹囊皮壤篷(DDRSR-20／40)遴行复求王程设计， 再引谶一套中20一80