51编程C51红外遥控解码程序适用于NEC编码格式的遥控器.docVIP

C51编程:C51红外遥控解码程序,适用于NEC编码格式的遥控器?[ltisn]? 这是小可之前写的,一直都在用.应用于NEC编码的遥控器接收解码,可靠性很高.特点介绍:简单易用,有重复按键识别功能.占用资源少,不需要定时器.欢迎各位提出不足之处,感谢.MSN:ltisn2008@?欢迎交流#include?AT892051.H//?遥控器地址码#define?IR_SYSCODE?0x00unsigned?char?ir_data;bit?ir_flag;unsigned?char?ir_repeat;void?ir_init(void){?IE?=?0x00;?EA?=?1;?IT1?=?1;?EX1?=?1;????/*?Enable?External?Interrupt1?INT1?*/??ir_flag?=?0;???/*?Initialize?ir_flag,?Receive?success?mark.?*/?ir_repeat?=?0;???/*?Initialize?ir_repeat,?Repear?mark.?*/?ir_data?=?0;}void?ir_svr(void)?interrupt?2{/****dataIR?0:?syscode0?????1:?syscode1?????2:?data?????3:?data?negation?????4:?0x00?end-mark??******/?unsigned?char?dataIR[4];?unsigned?char?width;?unsigned?char?i=0;?EX1?=?0;??/*?Disable?INT1?*/?width?=?0x00;/****常规状态下INT1为高电平，由高电平跳变为低电平时(即下降沿)产生中断****///?引导信号:9ms低电平?while(!INT1)?/***计算引导电平的宽度***/?{??delay_100us();??width++;?}?if?(width??80)???/*?8ms=80*100us?如果不到8ms视为干扰信号?*/?{??EX1?=?1;???/*??if?low-level?short?than?9ms,then?reset?receiver?*/??return;?}//?计算4.5ms低电平宽度???width?=?0x00;?while(INT1)??/*?Wait?for?boot?signal?4.5ms?high-level?*/?{??delay_100us();??width++;??/*?note?width?*/?}/*?判断是否是重复信号?2.5ms?*/?if?(width??30)??/*?3ms=30*100us?如果不到3ms即视为2.5ms重复信号?*/?{??ir_repeat++;??if(ir_repeat2)??{???ir_flag?=?1;???ir_repeat?=?0;??}??EX1?=?1;??return;?}?ir_repeat?=?0;/*?Receive?new_press?*///?4.5ms新键码引导电平?if?(width??40)???/*?4ms=40*100us?如果不到4ms视为错误信号，放弃接收?*/?{??EX1?=?1;??return;?}//?至此，引导码已校验，以下接收地址码和数据码，一共32位??while(i++??32)???/*?receive?32bits?*/?{??while(!INT1);??/*?Wait?for?0.5625ms?low-level?passed??*/??width?=?0x00;??while(INT1)??/*?Wait?for?data?signal?high-level?1?1680us;?0?560us?*/???{???delay_100us();???width++;??/*?note?high-level?width?*/??}??ir_data?=?1;??if?(width??0x08)?/*?identify?1?or?0?*/???ir_data?|=?0x01;???if?(i==8)????/*?note?IR_receive?data?*/???dataIR[0]?=?ir_data;??if?(i==16)???dataIR[1]?=?ir_data;??if?(i==24)???dataIR[2]?=?ir_data;??if?(i==32