K8排水槽DFM报告幻灯片.ppt

Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 尺寸分析 以上尺寸为装配后的尺寸，在单件产品无法测量，建议作为参考尺寸管控。 Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 外观认可 零件是否需要外观认可？ 如果需要外观认可是需要在哪里认可？ 请确认！ 1、无标准：MS-DB-500、PF-11203、SAE J2412、 ECE R21； 2、B1 B2定义是面还是圆轴心； 3、方框内尺寸是否体现在测量计划中？建议不体现； 4、未注公差尺寸怎么定义公差？参考GB/T14486-2008中MT5级执行； 5、平行度是否需定义基准？ 6、YS8 开口收缩变形后此尺寸有困难,建议到+0.15/-0.15; 7、1.65 ：零件收缩变形后整段尺寸不一致，只测量口部; 8、图纸上未注公差按照什么标准定义，包括YS12-YS16的公差定义 9、以上YS3、YS6、YS7、YS8、YS9、YS10做SPC管控，请确认。 * * Page Project name: K8-排水槽 Issue: DFM – Design For Manufacture - dated the 2016.10.23 重庆双玛科技有限公司 Engineering DFM-REPORT. Chongqing shuangma Technology CO.,LTD 产品信息 Product Information mould No: TBD Customer Name: TROUGH 排水槽 Customer mould No.: TBD Drawing No.: Trough_9526607 A01 Cavities: 1 *2 Material: PP+45%GF Part weight: 288g Part size: 900*102*37 Inch/mm: MM * Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 上下模分析 CAV/COR * Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 进浇口建议 Gate Advice 热嘴/3点达底进胶 针阀顺序式 浇口大小20*1.0 * 修浇口不易，有削缺风险； Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 结构分析 Structure analysis * 前模镶件位置示意，产品外观面上无镶件拼接线， Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 结构分析 Structure analysis * 后模镶件位置示意 Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 运水 * 前模水路示意 Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 运水 * 后模水路示意 Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG 结构分析 Structure analysis * 此两条槽斜顶出模，斜顶分型线位置有段差，可以控制在0.1mm以内 前模主要镶件示意 Customer comment. (please give your approval and comments) Date Approval by: Remark OK or NG * 前模此处做镶件，红线为分型线位置 后模主要镶件示意 Customer comm