sipa资料设备如何保证瓶坯质量(缺陷、原因、解决计划).docVIP

How to obtain Preform quality 如何保证瓶坯质量 代码 瓶坯缺陷 原因 解决方法 P1 Diffused opaqueness 放射状不透明 C15 C29 S19 S7, see causes/solut.P8 参照原因/解决方案P8 P2a All opaque – thread included 全部不透明—包括螺纹部分 C11 C48 S12 S48 P2b All opaque – thread excluded 全部不透明—螺纹部分除外 C35 C29 S27 S21, S7, see causes/solut. P8 参照原因/解决方案P8 P3 Bent as a “banana” 香蕉状弯曲 C4 C26 C17 C34 C10 S25, S3b S22, S14, S39 S15 S10, S8 S24 P4 Crystallized in the ring under the thread (support ring) 螺口下部结晶（支撑环） C6 C7 S3b, S40 S2 P5 Crystallized in the injecting point 注塑点结晶 C28 S20, S9, S18 P6a Incomplete in the thread 螺口不完整 C33 C19 C27 C5 C14 C13 C3 C7 S24 S1 S13 S3a, S1 S15 S14 S5 S2 P6b Incomplete in the body 坯体不完整 See P6a C38 See P6a S36 P7 Of yellowish color a) all 淡黄色 整体 b) on the bottom 底部 C8 C25 C27 C30 S12, S30 S21 S30 S18b P8 Too hot ( 100÷120 °C) 过热 (100—120度) C32 C2 C27 C34 C35 C12 C31 S6 S8, S31, S41 S30, S19b S8, S10 S26 S28 S6 P9 Too cold ( 100 °C) 过冷 (100度) C32b C35 C37 S6b S27 S8 代码 瓶坯缺陷 原因 解决方法 P10 Flash on the joint lip-cavity 模唇与模腔的合模线有凸起 C1 C21 C36 C27 C20 C2 C39 S14, S22, S31 S3b S3b S13, S18b, S21 S22, S31 S8 S42 P11 Flash at the edge of the mouth 嘴部边缘有凸起 C1 C1c C27 C21 C39 S14, S22, S31 C43 S13, S30 S3b S42 P12 Random hollow marks 不规则的凹痕 C10 C15 C14 C13 S24 S13, S30 S11 S11, S15 P13 Vertical flash in the thread - only 1 螺口部分有垂直的凸起 -只有一个 - all -全部 C1 As P11 S14 As P11 P14a Opaque diffused bubbles 不透明散布的气泡 C24 S12, S34, S19 P14b Not opaque diffused bubbles 透明散布的气泡 C12 S28, S33, S32 P15 Defective injection point (presence of flashes, threads or deformation in the center) 注塑点欠缺（出现凸起，螺旋或中部变形） C14 C13 C33 /o C33b C30 C38 S11 S11, S37 S25, S24 S18, S18b S36 P16 Thread deformed or flattened 螺口变形或变平 C16 S29, S31 P17a Vertical opaque con