《钢拉网筒单面点焊工艺研究论文》-毕业设计（论文）.docVIP

洛阳理工学院毕业论文 28 - 钢拉网筒单面点焊工艺研究 摘 要 钢拉网滤网筒是汽车安全气囊气体发生器的主要部件，它阻隔气体发生器引爆炸药的固体颗粒飞出打穿气囊袋。在引爆气体放出的同时，可将爆炸气体从1000℃以上冷却到300℃以下，防止其烧损气囊袋。比起传统的编织滤网及汽液分离网，刚拉网滤网筒在气体发生器上的应用由于其热蓄量大（冷却效果好）强度高（抗爆炸冲击力）而受到青睐。但由于其主要过滤及阻燃层采用高硅氧棉，对其制造工艺设计提出了新的课题。 本课题采用单面点焊结合电阻热固体连接技术来解决滤网筒网状焊接连接的工艺问题。本产品为复合滤网筒。 关键词：钢拉网，高硅氧棉，复合滤网筒 SINGLE-SIDED SPOT WELDING NET FILTER TUBE STUDY  ABSTRAC Steel filter cartridges are net Airbag gas generator of the main components, which separate the explosives detonated gas generator solid particles out of the bag went through the airbag. In the off gas released at the same time, the explosion could be more than gas cooling from 1000 ℃ to 300 ℃ under air bags to prevent them from burning. Compared to the traditional weaving and vapor-liquid separation filter net, filter net just in the gas generator tube applications because of its large amount of heat storage (cooling effect) of high intensity (the impact of anti-explosion) has been favored. However, as the main filtration and the use of flame-retardant high silica layer cotton, the design of its manufacturing process a new topic.  The combination of subjects using single-sided resistance spot welding heat solid connection technology to solve welding filter mesh tube to connect the issue of the process. The composite filter tube products. KEY WORDS: steel net, high silica cotton, composite filter cartridges 目 录 中文摘要…………………………………………………………,……1 ABSTRACT…………………………………………………,…2 目 录…………………………………………………………….……3 前 言……………………………………………………………….…5 第一章 电阻单面点焊焊接工艺…………………………………..…7 §1.1 电阻点焊原理7 §1.2 单面点焊7 §1.3 电阻点焊电极的选择9 §1.4 初始形核数值分析10 §1.4.1 随即形核阶段12 §1.4.2 扩散熔核阶段12 §1.4.3 熔核增厚阶段12 第二章 低碳钢工艺研究14 §2.1 低碳钢电阻焊焊接性14 §2.2 低碳钢预热和焊后热处理14 §2.2.1 预热14 §2.2.2 焊后热处理14 第三章 对钢拉网筒单面点焊的工艺研究16 §3.1 滤网筒原理16 §3.2 滤网筒分类16 §3.3 钢拉网筒点焊工艺研究18 §3.4 钢拉网筒点焊设备20 §3.4.1 摇臂式点焊机20 §3.4.2 电压式点焊机20 §3.4.3 移动式点焊机20 §3.5 点焊焊件分析20 第四章 电阻点焊在国内外的发展23 §4.1 恒流控制法监控方法23 §4.2 电极间电压法23 §4.3 动态电阻法…24 §4.4 能量控制法24 §