注塑模成型零部件结构和设计.ppt

Evaluation only. Created with Aspose.Slides for .NET 4.0 Client Profile 17.1. Copyright 2004-2017Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 4.0 Client Profile 17.1. Copyright 2004-2017Aspose Pty Ltd. 第5章注塑模成型零部件结构与被计 重点 分型面选择原则和案例分析 成型零件的设计与制造(含公式的运用)。 难点 分型面的选择和运用 成型零部件工作尺寸计算和型腔壁厚计算。 Evaluation onry. ith Aspose slides for NET 4o client P Evaluation only. Created with Aspose Slides for NET 4.0 Client Profile 171 Copyright 2004 -2017 Aspose Pty Ltd  Evaluation only. Created with Aspose.Slides for .NET 4.0 Client Profile 17.1. Copyright 2004-2017Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 4.0 Client Profile 17.1. Copyright 2004-2017Aspose Pty Ltd. 第5章注塑模成型零部件结构与设 1分型面的选择 5.2注塑模的排气 5.3成型零部件的结构设计 5.4成型零件工作尺寸计算 5.5型腔壁厚计算 Evaluation onry. ith Aspose slides for NET 4o client P Evaluation only. Created with Aspose Slides for NET 4.0 Client Profile 171 Copyright 2004 -2017 Aspose Pty Ltd  Evaluation only. Created with Aspose.Slides for .NET 4.0 Client Profile 17.1. Copyright 2004-2017Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 4.0 Client Profile 17.1. Copyright 2004-2017Aspose Pty Ltd. 5.1分型面的选择 5.1.1制品在模具中的位置 1制品或制品组件(含嵌件)的正视图,应相对 注塑机的轴线对称分布,以便于成型 2制品的方位应便于脱模,注塑模塑时,开模后 制品应留在动模部分,这样便于利用成型设备脱模; 3当用模具的互相垂直的活动成型零件成型孔、 槽、凸台时,制品的位置应着眼于使成型零件的水平 位移最简便,使抽芯操作方便; 4如果制品的安置有两个方案,两者的分型面不 相同又互相垂直,那么应该选择其中能使制品在成型 设备工作台安装平面上的投影面积为最小的方案; Evaluation onry. ith Aspose slides for NET 4o client P Evaluation only. Created with Aspose Slides for NET 4.0 Client Profile 171 Copyright 2004 -2017 Aspose Pty Ltd  Evaluation only. Created with Aspose.Slides for .NET 4.0 Client Profile 17.1. Copyright 2004-2017Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 4.0 Client Profile 17.1. Copyright 2004-2017Aspose Pty Ltd. 5长度较长的管类制品,如果将它的长轴安 置在模具开模方向,而不能开模和取出制品的; 或是管接头类制品,要求两个平面开模的,应将 制品的长轴安置在与模具开模相垂直的方向。这 样布置可显著减小模具厚度,便于开模和取出制 品。但此时需采用抽芯距较大的抽芯机构(如杠杆 的、液压的、气动