常用塑料特性及应用.pptVIP

Homopolymer POM [ CH2 – O ]n Copolymer POM [ CH2 – O ]n [ CH2 – CH2 – O ]m Homopolymer POM Copolymer POM HDT, 1820 KPa(°C) 125 110 連續耐熱溫度(°C) 100 100 彎曲強度(KPa) 96,530 89,635 抗張強度(KPa) 68,950 62,055 伸長率(%) 30 50 硬度(Rockwell) M94 M78 比重 1.412 1.41 均聚物(Homopolymer)：只含有一种重复单 元的聚合物 共聚物(Copolymer) 中文 聚丁烯對苯二甲酸酯 英文 Polybutylene Terephthalate (PBT) 重複單位化學結構 材料特性 # 電氣性優異； # 耐熱性佳； # 耐藥品性佳； # 耐熱水性佳； # 耐衝擊強度差 主要用途 以射出成型為主，產品包括電氣零件、開關及外殼、運動器材及汽車保險桿等。 聚丁烯對苯二甲酸酯 (PBT) [ (CH2)4-O-C- -C-O]n [ CH2-CH2-CH2-CH2-O-C- -C-O]n [ CH2-CH2-O-C- -C-O]n [ -C- -O-C- -C-O]n CH3 CH3 PBT PET PAR 柔軟 耐熱、剛性 SWATCHS塑膠錶殼, 透明, 比PC耐刮10倍, 耐高溫(抗煙頭) PBT、PET及PAR化學結構比較 PBT PET PAR HDT, 1820 KPa(°C) 65 100 175 連續耐熱溫度(°C) 60 100 150 抗壓縮變形強度(KPa) 75,000 86,000 93,000 衝擊強度IZOD, Notch(N-cm/cm) 53 26 215 抗張強度(KPa) 55,000 62,000 68,000 伸長率(%) 100 100 50 硬度(Rockwell) M70 M96 R125 PBT、PET和PAR特性比較 在爱护环境、珍惜资源、 持续发展的前提下，促进精实高效成型科技的发展与创新。 -先进成型技术学会- 问答 ？ 谢谢 ！ 設計高收縮率的結晶性塑膠射出成型品時，設計者應將壁厚變化限制在10%以內。 就低收縮率的非結晶性塑膠而言， 許容壁厚變化可到25%。 While designing injection molded parts in high mold shrinkage factor materials, the designer should try to limit wall thickness variation to 10%. The allowable wall thickness variation for the low mold shrinkage factor materials can be up to 25%. - Glenn Beall - 壁厚不均Non-uniform Wall Thickness 肋 Ribs If the part is to be molded in a high mold shrinkage material, such as polypropylene or acetal, the thickness at the base of the rib should be limited to 50 percent of the nominal wall thickness. Molding that same part in a low mold shrinkage material, such as ABS or polycarbonate, would allow the rib thickness to be increased to 75 percent of the nominal wall thickness. --- - Glenn Beall, IMM, Aug. 2000 - Make sure the vent size is large enough so that the air present in the cavity can escape during injection. Be careful, however, that the vent is not so large that it causes flashes in the vent. The recommended vent size is 0