泡沫沥青就地冷再生施工技术指导.docVIP

泡沫沥青就地冷再生施工技术指导 目 录 第一章 机械·······················································3 1.1 WR2500S就地冷再生 机···········································3 1.2 罐 车···························································3 1.3 压实设备························································3 1.4 平地机··························································4 1.5 准备工作························································4 第二章 再生材料配合比设计·······································5 2.1　原材料试 验·····················································5 2.2 材料要 求······················································5 2.3 准备试样并进行配合比设 计······································6 2.4 最大干密度和最佳含水量的确 定··································9 2.5 稳定材料的准 备················································10 2.6 成型试 件······················································11 2.7 确定稳定剂的最佳用 量··········································12 第三章 试验段施工···············································12 第四章 就地冷再生施工··········································13 4.1 就 地冷再生的工艺流程···········································13 第五章 养生及交通管制··········································18 第一章 机械 维特根冷再生技术施工是由一系列机械组合而成 的机组来完成的,机组中最重要的就是再生机械的选择。维特根系列产品中有很多种机械可用于再生，决定采用哪种机械主要受工程规模和类型的影 响。冷再生机械及配套设备的最低要求是有足够的生长能力并且处于良好的工作状态。下面介绍WR2500S型就地冷再生机在泡沫沥青就地冷再生施工过程中的机械配置和施工前的准备工作。 1.1 WR2500S就地再 生机 工作宽度:2438mm/3048mm 工作深度:500mm 发动机功率:500kW/680HP 工作重量:ca.32t 1.2 罐车 罐车是再生机的配套设备，用来供水或者液体稳 定剂。罐车的容量要与工程的规模和道路的几何形状匹配。在泡沫沥青就地冷再生施工过程中，要求两台罐车，一台是水罐车给再生机提供水；一台是沥青罐车给再 生机提供制作泡沫沥青的沥青材料。 1.3 压实设备 重型压路机对新再生层底部达到要求的压实度有 重要作用，因而其选择非常关键。在应用WR2500S泡沫沥青就 地冷再生机施工过程中需要三种不同的压路机。 1.3.1 双钢轮压路机 双钢轮压路机的主要作用是初压，并且把表面的 水分给封住，不让再生层水分流失过快。需要一台双钢轮压路机，可以选择自重20吨以上的压路机。 1.3.2 单钢轮压路机一台 重型压路机对新再生层底部达到要求的压实度有 重要作用，因而其选择非常关键。在应用WR2500S就地泡 沫沥青冷再生机施工过程中需要单钢轮压路机进行压实，数量1台－2台。泡沫沥青稳定再生结构层应用16t以上的单刚轮振动压路机结合胶轮压路 机碾压，单刚轮振动压路机可以进行强弱振选择。使用的单刚轮振动压路机静重取决于再生层的厚度，可参照表1.1选择： 表1.1??? 单刚轮振动压路机静重 选择 压实层厚度 压路机静重（吨） 150mm 16 150mm－200mm 20 200mm－250mm 22 250mm 25 1.3.3 胶轮压路机一台 胶轮压路机主要是对泡沫沥青再生层表面进行揉 搓，尽量让表面密实，减少水对再生