第一届网络课程大赛 科学注塑之应用 拓展学习：科学注塑实现热流道自动平衡.pptVIP

主讲：陈金伟 副教授 单位：广东轻工职业技术学院 Scientific Injection Molding * 拓展：科学注塑实现热流道自动平衡 * 依据模腔压力曲线，调节热流道温度 模具 / 产品 16 腔 16 个模腔压力传感器 8 个热流道(2 腔 / 热流道) 材料: PA 6 制品重量: 0,17 g 注射重量: 6,65 g 科学注塑实现热流道自动平衡 * Dt 1 2 3 4 5 6 7 8 模腔填充 流动不平衡 热流道自动平衡技术 * 1 2 3 4 5 6 7 8 模腔填充 Dt 流动不平衡 热流道自动平衡技术 * 1 2 3 4 5 6 7 8 模腔填充 Dt 流动不平衡 热流道自动平衡技术 * 1 2 3 4 5 6 7 8 模腔填充 Dt 流动不平衡 热流道自动平衡技术 * 1 2 3 4 5 6 7 8 模腔填充 Dt 流动不平衡 热流道自动平衡技术 * 1 2 3 4 5 6 7 8 模腔填充 Dt 流动不平衡 热流道自动平衡技术 * 监控设备 采集系统 模具内安装 压力传感器 模腔压力数据 设定值 一个周期后 参数 热流道自动平衡技术 * 调节工艺参数 压力出现时刻太早 熔体填充太快 压力出现时刻太晚 熔体填充太慢 降低热嘴温度 增加热嘴温度 压力出现时刻太早 压力出现时刻太晚 时间 模腔压力 时间 模腔压力 热流道自动平衡技术 * 1 2 3 4 5 6 7 8 模腔填充 热流道自动平衡技术 流动平衡 * 1 2 3 4 5 6 7 8 模腔填充 热流道自动平衡技术 流动平衡 KITECH April 2008 / Srr / 24 April 2008 Process Monitoring and Optimization based on Cavity Pressure Measurement / Daniel Fick / June 2012 KITECH April 2008 / Srr / 24 April 2008 Process Monitoring and Optimization based on Cavity Pressure Measurement / Daniel Fick / June 2012 Process Monitoring and Optimization based on Cavity Pressure Measurement / Daniel Fick / June 2012 Process Monitoring and Optimization based on Cavity Pressure Measurement / Daniel Fick / June 2012 Process Monitoring and Optimization based on Cavity Pressure Measurement / Daniel Fick / June 2012 Process Monitoring and Optimization based on Cavity Pressure Measurement / Daniel Fick / June 2012 Process Monitoring and Optimization based on Cavity Pressure Measurement / Daniel Fick / June 2012 Process Monitoring and Optimization based on Cavity Pressure Measurement / Daniel Fick / June 2012 Process Monitoring and Optimization based on Cavity Pressure Measurement / Daniel Fick / June 2012 Process Monitoring and Optimization based on Cavity Pressure Measurement / Daniel Fick / June 2012 Process Monitoring and Optimization based on Cavity Pressure Measurement / Daniel Fick / June 2012 Process Monitoring and Optimization based on Cavity Pressure Measurement / Daniel Fick / June 2012 Process Monitoring and Opti