RationalDMIS赋值取值功能发现.pdf

RationalDMIS 赋值取值功能发现 2016-07-22 山涧果子 提示: 拖放式操作，快速赋值，取值，方便测量！ 根据图纸建立工件坐标系 DMISMN/Created by [爱科腾瑞(CNC).12.9] on 星期五, 七月 22, 2016, 4.0 UNITS/MM, ANGDEC WKPLAN/XYPLAN PRCOMP/ON TECOMP/ON FLY/1.0 MODE/MAN SNSET/APPRCH, 2.000000 SNSET/RETRCT, 2.000000 SNSET/DEPTH, 0.000000 SNSET/SEARCH, 10.000000 SNSET/CLRSRF, 10.000000 RECALL/D(MCS) SNSLCT/S(ROOTSN1) GEOALG/CIRCLE, LSTSQR GEOALG/ARC, LSTSQR GEOALG/PLANE, LSTSQR $$ $$ MODE/MAN F(PLN1) = FEAT/PLANE,CART, 39.744618, 27.920561, 0.000000, 0.000000,$ 0.000000, 1.000000 $$ Measurement points are created through actual points MEAS/PLANE, F(PLN1), 4 PTMEAS/CART, 9.599796, 46.402035, 0.000000, 0.000000, 0.000000, 1.000000 PTMEAS/CART, 22.513281, 7.451381, 0.000000, 0.000000, 0.000000, 1.000000 PTMEAS/CART, 64.409935, 4.694489, 0.000000, 0.000000, 0.000000, 1.000000 PTMEAS/CART, 62.455460, 53.134338, 0.000000, 0.000000, 0.000000, 1.000000 ENDMES D(CRD1) = DATSET/FA(PLN1), ZDIR D(CRD1) = TRANS/ZORIG, FA(PLN1) F(LN1) = FEAT/LINE,BND,CART, 6.753366, 0.000000, -3.845330, 76.717239,$ 0.000000, -3.203002, 0.000000, -1.000000, 0.000000 $$ Measurement points are created through actual points MEAS/LINE, F(LN1), 2 PTMEAS/CART, 6.753366, 0.000000, -3.845330, 0.000000, -1.000000, 0.000000 PTMEAS/CART, 76.717239, 0.000000, -3.203002, 0.000000, -1.000000, 0.000000 ENDMES F(LN2) = FEAT/LINE,BND,CART, 0.000000, 4.658314, -3.457176, 0.000000,$ 53.603622, -3.374311, -1.000000, 0.000000, 0.000000 $$ Measurement points are created through actual points MEAS/LINE, F(LN2), 2 PTMEAS/CART, 0.000000, 4.658314, -3.457176, -1.000000, 0.000000, 0.000000 PTMEAS/CART, 0.000000, 53.603622, -3.374311, -1.000000, 0.000000, 0.000000 ENDMES F(PT_INTER1) = FEAT/POINT,CART, 0.00