第2章 单片机输入输出应用.ppt

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * LCD12864液晶显示程序设计如下。 #includereg51.h #define uchar unsigned char sbit CS1=P2^4; //片选左半屏的管脚定义 sbit CS2=P2^3; //片选右半屏的管脚定义 sbit LCD_RS=P2^2; //H数据输入，L指令码输入 sbit LCD_RW=P2^1; //H读取，L写入 sbit LCD_E=P2^0; //使能，由H到L完成使能 uchar code matrix[]={ /*-- 文字: ※ --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/ 0x00,0x82,0x84,0x08,0x10,0x20,0x46,0x86,0x40,0x20,0x10,0x08,0x84,0x82,0x00,0x00, 0x40,0x21,0x11,0x08,0x04,0x02,0x31,0x30,0x01,0x02,0x04,0x08,0x11,0x21,0x40,0x00, /*-- 文字: 单 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/ 0x00,0x00,0xF8,0x49,0x4A,0x4C,0x48,0xF8,0x48,0x4C,0x4A,0x49,0xF8,0x00,0x00,0x00, 0x10,0x10,0x13,0x12,0x12,0x12,0x12,0xFF,0x12,0x12,0x12,0x12,0x13,0x10,0x10,0x00, /*-- 文字: 片 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/ 0x00,0x00,0x00,0xFE,0x20,0x20,0x20,0x20,0x20,0x3F,0x20,0x20,0x20,0x20,0x00,0x00, 0x00,0x80,0x60,0x1F,0x02,0x02,0x02,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x00, /*-- 文字: 机 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/ 0x10,0x10,0xD0,0xFF,0x90,0x10,0x00,0xFE,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00, 0x04,0x03,0x00,0xFF,0x00,0x83,0x60,0x1F,0x00,0x00,0x00,0x3F,0x40,0x40,0x78,0x00, /*-- 文字: 液 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/ 0x10,0x60,0x02,0x8C,0x00,0x84,0xE4,0x1C,0x05,0xC6,0xBC,0x24,0x24,0xE4,0x04,0x00, 0x04,0x04,0x7E,0x01,0x00,0x00,0xFF,0x82,0x41,0x26,0x18,0x29,0x46,0x81,0x80,0x00, /*-- 文字: 晶 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/ 0x00,0x00,0x00,0x00,0x7F,0x49,0x49,0x49,0x49,0x49,0x7F,0x00,0x00,0x00,0x00,0x00, 0x00,0xFF,0x49,0x49,0x49,0x49,0xFF,0x00,0xFF,0x49,0x49,0x49,0x49,0xFF,0x00,0x00, /*-- 文字: 显 --*/ /*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/ 0x00,0x00,0x00,0xFE,0x92,0x92,0x92,0x92,0x92,0x92,0x92,0xFE,0x00,0x00,0x00